Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
s132 4.0.2, nRF5 SDK 13. In BLE_GAP_EVT_CONNECTED event handler I try to call sd_ble_gap_data_length_update returns NRF_ERROR_RESOURCES.
I have
#define NRF_BLE_GATT_MAX_MTU_SIZE...
Hi all,
I have some question want to ask.I have about 200 bytes to write to the flash and also I would use the bootloader.
I'm using nRF5_SDK_11.0.0_89a8197 and s130_nrf51_2...
This test program is modified from examples\pin_change_int\main.c, I add the instructions to put the cpu to sleep. And I add nrf_gpio_input_disconnect() for all the pins except...
Hello, I am using pstorage function and I would like to know oppionions of your's what would be the best practise to wait until processor erases the flash memory and would...
Is enable required before configuration? Does toggling NRF_ADC->ENABLE reset the configuration (like it does for the radio?) Is the power to the ADC automatic, so that even...
im using sdk10, I initialiszed ble_stack_init and advertising_init but when starting advertising, it works with BLE_ADV_MODE_FAST but not with BLE_ADV_MODE_SLOW .
why it...
Hallo comunnity
I have a sensor which is working is sending data via BLE and it has a 128 UUID bit service [0x 000000-000000-1000-8000-0080-5F9B34FB]
In order to do...
Hi,
What is available MTU of CoAP and UDP over 6lowpan with IoT SDK ?
In my application, I need to transfer dozens of kb data to ble node over 6lowpan with iot SDK. Do...
Hi, I bonded is ok .But I want to store some data on nrf51822 flash memory using pstorage. What should I do?
Register new or change it :
param.block_size = ALL_CONTEXT_SIZE;...
I have an SPI peripheral that has an odd protocol and in trying to sort out why it was acting up I finally caught a logic trace showing about a 13us break in the SPI data...
Hello,
I am using HID mouse/keyboard examples from SDK to learn creating custom HID device.
Besides using four buttons on EVK to simulate motion action. I would love...
Hi All,
I'm currently setting up three nRF52840 DK nodes, two nodes are routers and one is an end-device. My plan is to introduce more node in the network later on. The...
Hi,
We created a faster & simpler alternative to gazell for the nRF24LE1 (our IoT sensor) that supports 100s of transmitters (PTXes), is individually addressable, has session...
