Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I am trying to run the debug project for ble_app_hrs following the steps in "nAN-29 nRF51 Development with GCC and Eclipse Application Note v1.1.pdf"
but I get this error...
Given that most of the SDK (including the softdevice hex) is public now due to the mbed support: would it be possible to open up the downloads for the standard nRF51 SDK and...
From the s130 release notes:
GAP
Concurrent Central, Peripheral,
Broadcaster and Observer operation
(DRGN-4354).
Up to 4 simultaneous
active connections...
Hi.
I am trying to modify the bootloader example provided by nordic.
I am able to compile/link my code and use nRFgo studio to run it, but for some reason I can not debug...
Hello,
i´m using nRF51822 with S110 SoftDevice to transfer data from Sensors that will be read out via I2C by the Nrf51822.
I have read some topics about how it is not...
Hi,
I bought nordic evaluation board 2 days ago. I have been searching through the forums to enable and test the voltage level of a battery and monitor it via UART. After...
Hello all,
Is it possible for a nRF51822 to read information from another peripheral Device using broadcasts or advertisments?
I have an application where I need to...
hi,
I have been reading some posts regarding similar issues, but I am not able to nail down this one.
I am trying to create a custom 128 UUID and associate some Service...
I overwrited the application program which made with v5.1.0 and it included only difference against the v5.1.0 to sdk v6.1.0. After this, I buidled it but the target didn...
I am looking for a dev kit which would allow me to try out SoftDevice S130, will I be able to use S130 if I buy any of these:
nRF51822-mKIT
nRF51822 DK
nRF51822 EK...
The nrf51 reference manual shows timing diagrams for the TWI interface when reading from slaves to have a shortcut between BB and SUSPEND. My assumption would be that's there...
I am using the ble_app_uart code from SDK 6.0 on my custom PCB with a nrf51822. I am comparing it's functionality with a PCA10004. Both are running the exact same code. I...
Hi all,
some time ago we bought a nRF51822 Evaluation Kit with the PCA10001 being Version v2.0.0.
Why exactly is it not recommended to work with the new SDKs such as SDK6...
Has anyone played with getting the iBeacon reference kit/software to run with the SD7.0 code?
I'm wanting to change from the boot loader + SD 6 + app to a simpler SD 7...
I have download the puck-central-android code from the following link
github.com/.../puck-central-android
I can build the project and successfully programmed in the android...