Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
Nordic,
I am using the BLE Shield v2 and the Arduino Due board to transmit accelerometer/gyro data to an Android tablet app that plots this data. I had this working fine...
First I noticed that nordic has already updated the andriod nrf toolbox app to use softdevice v7, which allows updating the softdevice, bootloader and application.
The...
Hello all,
I'm working on a library for NRF24L01+ and PIC micro.
Unfortunately there is something wrong. On the receiver side, the micro correctly detects that a packet...
Hi,
I am knew to BLE and I was able to ran succesfully the blinky project. Now when I load the soft device on and then try to download the hr example if says "Flash download...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
Hi,
I develop an application with the nRF51822 circuit. It is detectable with my smartphone, but not with a computer that has a Bluetooth 2.1 device. Is it possible to...
In the comment of this post , Marc Nicholas wrote:
Doesn't that require SWO to be implemented? (Which is not on the Nordic part).
Is it true, that SWO isn't available...
In SDK 6.0 I find there is a project of ble_app_hids_keyboard_serialization.uvproj in nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
and it contain...
Hey there,
today I'd tested around with the Dfu service.
Peripheral is nRF51822 running Sdk 5.2.0 bootloader example (Softdevice 6)
Central is Android 4.3 running...
I am unclear whether the soft radio takes care of updating the attribute when a write event occurs. I can see in the example codes that the notification flag is handled by...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
