Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi:
I purchased the nRF5340 Audio DK and used NCS 2.5.0. After flashing the unicast_audio_client example (zephyr/samples/bluetooth/unicast_audio_client), it failed to run...
Our project is built wit NRF Connect SDK 2.9.0. For the UART we use nrfx_uarte library directly.
RX works perfectly, but TX is working only in blocking mode. If I call ...
Hi,
I designed a custom NRF52832 board and need to connect it to an ESP32 board. I soldered five boards for testing and also have an NRF devkit.
However, the ESP32 only...
My platform is the NRF5340 , coupled with 32MB of external flash , so I have plenty of external storage available. However, there's a risk that my project may eventually outgrow...
Hi there,
we're currently in the process of changing our hardware to use the nRF54L15. Since all the security regulations are getting stricter and stricter and the support...
I'm looking at Product Specification v1.2 - Reference Circuitry Configuration 2 where BUCK2 is not used. The schematic shows the output VOUT2 is tied to VSYS in this case...
Hi Nordic Team,
I am planning to develop a Matter-over-Thread end device (sensor) using the nRF54L15 , which will be battery-operated . To maximize battery life (minimum...
Does anything exist yet? The datasheet only contains a preliminary matching network and says will be available when the chip enters mass production, but nothing is available...
I tried used Nordic's UART service implementation as a starting point and everything works but I can't figure out where the string "Nordic UART Service" from "nrf connect...
I have loaded the Quick Start Application using nrf connect for Desktop after following the instructions. I get the error as per the attached file on the Serial Terminal....
Hello,
We are trying to test our custom board with nRF9161 in a new location, so we bought local SIM cards (Yettel, Serbia) here. These are not special nb-iot SIMs, just...
Is there a way to modify the distance measurement sample code to where it is intended for one transmitter and multiple receivers versus between just two devices? I am trying...
The workaround says:
" Trigger TASKS_PLLSTART before TASKS_XOSTART is triggered and trigger TASKS_PLLSTOP after TASKS_XOSTOP is triggered."
I would like to start HFXO...
Hi,
I am running into a really strange issue where setting both CONFIG_NRFX_PWM0=y and CONFIG_NRFX_PWM1 =y in prj.conf gives me the following build errors while using mcuboot...
Hello,
My PPK2 is reporting 2 zetta amperes power usage, and I found out that the "modifiers" appear really broken:
I have attempted to re-flash the ppk2 firmware, but...
