Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Excuse me:
The SPIS example in SDK is shown in the figure below,the m_rx_buf buffer has only seven bytes，Does NRF_DRV_SPIS_XFER_DONE event occur when the buffer is full...
I am developing a NRF52810 product, I am downloading using JTAK on NRF52832 development board.
I have the NRF52810 because of the lack of IO pins. SPI CLK , TWI CLK are...
I use the NRF Mesh SDK v2.2.0
- EVB PCA10040 burn the serial example
- EVB PCA10056 burn the light server example
- PCA10040 attach to the Raspberry Pi 3 via USB for...
I'm trying to follow these instructions to update the openthread binaries in nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
I have a Windows host machine and a Ubuntu VM...
Hi,
I am trying to do AGPS with the supl library. I obtained version 0.7 through the application and installed it (and enabled the required config options).
Unfortunately...
Hi Nordic,
I am working on project with nrf52840 , which is a central to connect other device. we will enter the MAC address to central, and setup the scaning filter.
...
Hi all,
I am trying to do bonded buttonless DFU but an error named NRF_ERROR_FORBIDDEN was raised in enter_bootloader() function under ble_dfu_bonded.c.
The description...
hi，
I currently have an application scenario，using a nRF52832(M board) BLE maser to upgrade another nRF52832(S board) is run standard DFU ，Are there any demo available？
Previously, I used SEGGER to build and run programs on nRF52 DK very quickly (5-20 seconds).
However, for nRF5340 DK, it usually takes about 8-15 min to build and run just...
Hi,
I am trying to connect the current product with MCU EFM32GG290F1024 to a Nordic BLE module in a serialization over UART.
I have port the SDK to my project and need...
1. hardware : nRf52840 dongle.
2. Purpose : Update Firmware into dongle to be sniffer, and restore original default manufacturer firmware for nRF Connect v2.6.0 desktop...
Hello All,
i my project there are 2 ble services now i want to add Flash read/write application i tried with fds as well as flash_write example from the SDK 15.3.0
i added...
Hello!
Apologies in advance for my english.
I already asked a similar question, here is the link to it
When trying to connect a PWM driver PCA9685, I ran into problems...
