Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I'm using NRF52832 with S132_3.0.0 and the SDK version is 12.2.0.
When NRF53832 was bonded to a mobile phone, I try to use "pm_peers_delete()" to delete the bonding information...
I am looking for a way to start advertising as soon as connection event.
Our use-case is: we have 1 peripheral that's connected on CODED PHY to a central with a relatively...
Hi,
I am using softdevice s140_nrf52_7.0.1. I am trying to send the SAADC calculated voltage over NUS to a gateway. For like 20-30 seconds the program works fine and the...
Hello,
nRFSDK5 v16.0, device nRF52840, Softdevice v7.0.1
I am trying to write some data periodically onto device flash memory using FDS Lib, occasionally I come across...
Hello
I'm trying to reenable notifications on a characteristic from GATTS side
The device is 52810 running a custom service and this is the piece of code where i use ...
I am trying to pair my nRF52-DK with my Fitbit device for testing purposes. I am currently using the nRF Connect v3.6.1 desktop application. I can scan and connect to the...
When I run my code using Segger debugger, all is well and I can read and write from flash with issues. However, when I run the same code independently I sometimes get:
ASSERT...
For an ongoing product certification in China, I need to provide the certification lab with the Direct Test Mode application that is available from the nRF Connect suite on...
Hi,
I'm using the NRF52832, as peripheral, to read data from a HTS221 sensor via I2C.
I'm using the TWI_sensor module following this example , but I want it to enable...
Which digital IO pins on the nRF9160 support interrupt on pin change?
I'm implementing an antenna MUX control routine where the MUX control (3 pins out of nRF9160) depends...
Currently working on an IOT solution based on the nrf 9160 SIP that supports both firmware and modem firmware updates in combination with Zephyr and the nrf SDK. During the...
Hi there,
I am studying the nRF9160 DK with the DHT sample from Zephyr, but I fail to build it as error of "'DT_N_INST_0_aosong_dht_P_label' undeclared (first use in this...
Hi,
I am searching the examples in SDK related to security concepts like pairing,bonding and encryption.
And I found ble_app_gls example in SDK 17.02.
Can you please...
