after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
this is my first time trying to use nrf connectivity tools, and my setup is a bit strage (and I have no clean DK setup to compare with:-(
I have to update firmware...
I am developing an IEEE 802.15.4 Application on the nRF52840 using the Radio Driver (v1.8.0) . I have a problem with the transmit call function. Very often in nrf_802154_transmitted_timestamp_raw...
I wrote a program for nRF51822 and compiled it with keil. The app, boot, and sdk are combined and written to the chip. However, if I write using nRF Connect Programmer, it...
Hello,
Our custom board (nrf52832, S132) seem enter to the read back protection, J-Link could not connect to the target in any ways.
We tried the command "nrfjprog --recover...
The code is running on 52832 (BLE) and transmit msg over BLE (NUS) each time GPIO is active (GPIOTE).
But same code (after adding LE CODED Phy) is crashing once it reached...
I am trying to build the NCS sample project "peripheral_lbs" with multiple peripheral connections. Therefore I added the CONFIG_BT_MAX_CONN. Up to 20 the build is working...
I have a problem when activating the simcard via nrf connect. |
After several attempts, using the IMEI and PIN on the Thingy 91 product, i get the following error.
(There...
Hi. How do I advertise both heart rate service and current time service together?
Seems like the current time service overwrites the heart rate service.
I will appreciate...
Trying to convert a working sample for a BME280 sensor from I2C to SPI
nrfConnect 1.4 on nrf9160-DK
After looking at other SPI examples and noting the syntax I thought...
Hi,
i have changed uart pins to second port. After that it is not advertising. when i connect the FTDI converter to the uart pads from custom board, it starts working and...
Dear Devzone Community,
when trying to get the Zephyr SHT31 Sample running, I stumbled across an error which I was not able to resolve.
I did the following:
Add nrf9160dk_nrf9160ns...
I need to control the BLE ON/OFF state and send some data to MK81 via BLE through UART, we have estalished the Hardware connection between the nRF52832 chip and MK81,
How...
So, I am quite beginer with programming and working with this sensors and nrf, So I need your guys help.
I am trying to get the x,y,z values from the accelerometer of BMX055...
The nRF 52840 RSSI "meter" is not usable.
I tested in an RF (2.4Ghz) quiet neighborhood. Using a reference receiver, I measured RSSI variance around +/-3 dB (95% confidence...
