after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
Hi, I've been given an nRF52 devkit and have been tasked with programming to generate a 2.4GHz signal. The requirement given to me is that simple. (I believe an RF expert...
I'm using nRF Connect for VSCode to program my nrf5340dk but the SDK can't detect my nrf5340 on the boards (You can see in the image). Can anybody help me to fix this problem...
Hello,
As soon as we enable CONFIG_BOOTLOADER_MCUBOOT and have an operational MCUBoot image, we noticed that our audio pipeline is no longer working for our i2s omni-microphone...
My attempts to configure the Zephyr device tree to run littlefs on an external SD card have repeatedly resulted in what appears to be the creation of a small littlefs instance...
I was doing a demo code to implement a wake up triggered by motion. I was able to make it work with the integrated low power accelerometer on thingy52 but it only worked 1...
Hello,
Although I already used the nrf52840 on previous projects (nrfxlib), I'm a newbie using nRF Connect and ZephyrOS (I previously used RTOS).
I'm integrating a driver...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello Nordic team,
I'm currently developing on the nRF5340 and recently encountered an issue related to BLE advertisements . After thorough debugging, I was able to confirm...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hello, I am working with the nrf52832 and was trying to understand the steps for configuring the Bluetooth stack. Does anyone know what role the APP_BLE_CONN_CFG_TAG plays...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
I have an application that I want to build and run on 5 or 6 target devices including a nRF52840DK, nRF52840 Dongle, and custom boards. There are areas of the code that only...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
