Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
We are developing product that developed using USB, Zigbee and BLE of nRF52840. We dont want to for new VID registration for just one product and thinking of using VID...
Hi!
I am trying to get a basic NRF_LOG_INFO("some text here"); to print text to a terminal in Segger Embedded Studio. I'm using Termite as the terminal and SDK 15.3.0. To...
Hi
I am using nRF52840 DK for development and using nRF-IEEE-802.15.4-radio-driver code from SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
I want to implement functionality...
Hello,
I am newbies on nrf51 and keil uvision 5.
I just start to learn nrf51 development.
I saw that with keil 5, it is possible to flash Sofdevice directly from IDE...
Maybe the question is abnormal, but is it possible to make the NRF24LE1 chip work on the Sub 1GHz band by setting the quartz to a lower (less than 16 MHz) frequency? Has anyone...
Greetings....
Since logging is removed from Mesh, I find it is very hard to debug the system. I wonder if it is possible to ask for your help to have a new monitor type...
SDK v15.2.0 using code from the peripheral spi example. Linux Ubuntu 19.04, uploading to nRF52 DK.
When I call my get_bma253_accel_data in main, I get a continuous stream...
The development of the custom hardware of an nRF52832 utilizing the u8g2 library has been shown to control a small display 64x48 SSD1306 driver. The prototype hardware another...
I have been migrating a project from SDK 14.2 to SDK 15.3 and have encountered an issue with UART. I am using the legacy layer with the following configurations:
I am...
Hello,
I'm evaluating nRF52811 as a long-range IC in a beaconing application.
Here's our specifications:
- The beacon must operate with Coded PHY
- The application...
Hi everyone, I know that the theoretical limit for the Bluetooth Low Energy throughput is 1 Mbit/sec, but I heard that on practice you get much lower. So I would like to find...
We were running BLE DFU bootloader for nrf52832 based on sdk 14.2; this worked fine.
We have now moved to sdk15.3 and nrf52840 as we needed USB.Our applicaton is up and...
Hello,
I have a custom nrf9160 device which requires
device stops at:
'Secure Boot: prepare to jump to Non-Secure image'
if I use this the following prj.conf:
...
