My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi
After upgrade modem to mfw_nrf9160_1.0.0.
Most of our SIM cards still working good on both AT and MQTT projects.
Two of our SIM cards can't connect to LTE when uses...
Hi,
I'm using nRF52840 where it's written 1.0.0 on the jlink ship and QIAAC0 on the nRF ship.
When reading the info.variant register I got 0x41414330 which is ..AAC0...
Hello everyone,
I am using a NRF52840 development kit to write a custom protocol, so for the moment I am not using the softdevice but I am rather using the Radio as a...
We have a board built with the NRF9160 and an ADE9153A. The ADE9153A only responds to messages with odd parity. How do we set the NRF9160 to odd parity?
Hi,
I want nRF52 Continuous Unmodulated TX carrier.
Is it possible by TASK_TXEN and TASK_START or radio_tx_carrier command of radio test example, after TX configuration...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hi, team I am trying to build a system with one master and multiple slaves using the mesh SDK. ( This is similar to the light_switch example. ) At this, I want to give each...
After the update to nRF Connect v3.0.0 none of the Nordic devices is detected anymore by that tool.
I even un-installed and reinstalled nRF Connect v3.0.0 (as recommended...
Went through the pin_change_int example and of course it works fine.
Migrated that to custom board and it also worked fine with main loop.
So I then tried to use that...
Have an application that configures a wifi SOC using spim before enabling BLE scanner.
When it is running there are 4 timer events running and the main loop check status...
Hello,
Zephyr 1.14.0 includes the nrfx code to use GPIOTE and PPI and my code compiles but I get
undefined reference errors to the nrfx_gpiote_ and nrfx_ppi_ functions...
Few issues I'm facing -
1. I have gone through the related blogs, tutorial, documentation for DFU. nRFConnect cannot connect to the Fanstel BM832 chip. It gives me an error...
hi
I connect AT24C02 EEPROM with nrf52dk.
I already test EEPROM with arduino and it work fine.
Now i want to communicate with NRF52DK kit,so which example I would prefer...
