Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
I am using mbn52832 BLE+MCU module and i am facing issue in one of the GPIO pins.
I am facing issue in P0_29 pin and i am driving the P-channel MOSFET from this pin. I have...
Hi,
I would like to configure the watchdog timer for the nRF9160. I have attempted to run the Zephyr example application (path/to/zephyr/test/driver/watchdog/wdt_basic_api...
Hi:
i am working with Thingy52，and i have get a zip pack named thingysdkv210,today after the compile prcess after following ../PCA20020/thingysdkv210/documentation/firmware_compile...
My problem:
I have to setup a BLE connection between two nRF52 devices one central device and one peripheral device. I have multiple central devices (C1, C2 to Cn) and multiple...
We are developing BLE 5.0 products using the nRF52832 running the Nordic S132 v6.0.0 softdevice and SDK version 15.0.0.
We noticed that one of our test devices, a Huawei...
Dear all,
I am trying to develop an application that reads data from a sensor (accelerometer) and I want to be able to update the advertisement packet with the measurement...
Hi, I am using nRF52832. I want to update my boot loader using DFU, I am unable to find correct command to get .zip file. I am using below command:
nrfutil.exe pkg generate...
Hi,
For my home Mesh network, I use a Android mobile phone + nRF Mesh App as a mesh provisioner to configure the nodes, and control the mesh node as well.
There're about...
Hello，
When I use the nRF9160 to upload the data to the cloud based on the LTE-CatM1, what's the maximum current? The datasheet of nRF9160 mentioned:
1. Application CPU...
Hi all,
I'm struggling with UARTE and easyDMA. i just want to send data with TX.
I am trying to configure it with the hal librairy but i cannot manage to make it work...
Hi I would like to, at app level, implement access control to characteristic. My characteristic is configured solely as notify (no read, no writing).
When a smartphone turns...
I am testing about tx power level on nRF5_SDK_15.3.0_59ac345 with nRF52840.
I have some confusing about sd_ble_gap_tx_power_set() function.
In peripheral advertising...
Hey guys I want to resolve some issues regarding RSSI values received from BLE beacons. I have ibeacons type.
1: Ibeacon format says the last byte is signal signal, is it...
Hi, after following the tutorial about building the asset tracker firmware I came to the problem of generating merge.hex file. The zephir.hex file is generated, but the merge...
chip: nrf52840 aQFN package
5~10% of the products were defective. by causing analysis, There are short some pins bottom of chip.
I already read this guide after this...
