Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello, I've been evaluating the PDM hardware driver for the nRF52832, and the PCM output of Thingy. I've found that, for certain impulses at the input of the microphone, the...
Hi I have successfully set up my ARM SPI interface to use the nRF24 chip. At this time I'm trying to establish connection but I'm not sure I under stand the setup for comm...
I'm getting this when im trying to select the device.
when i try to update the firmware nrfgo studio is getting closed
please help me in solving this!!
Let's first compare two pieces code:
This one works:
But this one doesn't:
My problem is that as soon as I try to process received data, some of data is lost. Is...
I am developing with SDK 15.0.0
I want to add NUS service in ble_app_buttonless_dfu example.
All I have done:
1. Add including files and including paths to the project...
This is really a two part question.
1. How do I even refer to pin P1.00? It's clear that pin P0.06 is referred to simply as pin 6, but what is the naming convention for...
Hi,
i try without succes to go into MemoryRentention Timer On sleep mode, and wakeup with the analog comparator activated by AIN1 without sucess. Here is my code, please...
Hello I am using nrf52832. I would like to write a custom ISR for GPIO based interrupt. Are there any examples/documentation i could use to get started on this.?
Dear All,
we use Reference configuration 4 and have connected the DK to our custom PCB. 3.3V of the DK go into VDDH and otherwise only GND and SWDIO/SWCLK are connected...
hi
i downloaded nordic thingy52 FW and i uploaded on my board PCA20020
and that is working correctly but when a i downloaded nRF5_SDK_15.0.0 at first i compile (ble_app_beacon...
Dear Nordic,
i am just testing ble examples in nrf 52840 dongle and also implementing one uart for just testing
TX pin - 1.10
RX pin - 1.13
transmission works fine...
Hi,
I'm referring to -
1. Custom HID over GATT device
2. nRF51422 HID example modification
So for now, I just used the descriptor mentioned in above links. But "hello...
Hello,
The softdevice S132_SDS_v4.1 spécification write that supports 20 connections at the same time.
I would like to know if it's possible to have 1 central and 20 peripherals...
I'm attempting to make cli application to load from after the softdevice and based on a command enable/disable the BLE functionality. Is there any simple way to do this? Are...
Hi,
I am currently trying to use PCA10001 board as master and slave at the same time. Trying to send data from master(SPI0) and receive it using slave (SPIS1).
I have set...
