Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I tried building ' pca10040 ' configuration of " nrf52-mpu-easydma-using-gpiote-and-registers " example from " https://github.com/Martinsbl/nrf5-mpu-examples ". The following...
Hi
I am working on nRF51-DK with Mbed IDE & used PWM example code from link : https://os.mbed.com/handbook/PwmOut
When enabled PwmOut, PWM signal is observed on the oscilloscope...
I would like advice on whether the following is a valid ble transaction.
We have a product with the nrf52 in it running sdk 12 and softdevice 3.0. This is setup as a a peripheral...
Hi,
I'm using nRF5 SDK v. 14.0.0. I'm trying to pass a context pointer to the NRF_SDH_BLE_OBSERVER macro, but am running into compilation errors. I want to do something...
Hi,
I'm building a project with nRF52832 dev kit and the SHT10 temperature and humidity sensor, I'm searching for a library/example project of this sensor and the nRF52...
I'm planning to make a custom board using Thing52, following the reference desing. I have some questions (1) Can I use nRF52840 instead of nRF52832? (2) Do you provide an...
To reduce power consumption during sleep I have to completely disable the UARTE0. This is done before sleeping by :
NRF_UARTE0->TASKS_STOPRX = 1; NRF_UARTE0->ENABLE = UARTE_ENABLE_ENABLE_Disabled...
We are using Bluetooth Developer Studio along with Nordic's code generator plugin (Nordic Semiconductor nRF5 1.3.0 SDK 14.0) for our project.
We've made a couple of improvements...
Hi!
I got an error while compiling the proxy client example in BLE Mesh SDK V 2.0.0 as The object file build/light_switch_proxy_client_nrf52832_xxAA_s132_6.0.0_Debug/obj...
HI al
I have a bicycle computer (A) host (SDK 12.1 51822QFAC S130-V2.0.1) and a slave device (B) for measuring bike speed and cadence (using 2032 batteries). 1. When the...
Hi, I was recently asking about OPUS - https://devzone.nordicsemi.com/f/nordic-q-a/32875/how-compile-opus/128181#128181 . Now I am able to run encode on audio data and decode...
Hi
We have a nrf51 dongle for use in a school prosject When the nrf51 dongle is connected to the USB slot in a computer it boots fine without holding the button when powering...
On the Getting Started page, I do not see the USB described in Step 7. I do not see any device. The LEDs flash and the buttons light up LEDs 1-4 as described.
Thanks
Hi,
I'm using nrf_serial 'object' in order to communicate nRF52832 with an external device.
As I work in non-blocking mode I need to verify if there's available space...
