I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
Hi,
I'm using SDK13.0.0 and softdevice S132 v.4.0.2.
I sometimes get NRF_ERROR_INVALID_STATE from sd_xxx() in the function registered to ble_evt_dispatch() when connection...
Hello,
I would like to establish communication between my pca10040 and my cellular modem.
Currently I am using ble_app_uart on the peripheral example and I can put messages...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I have a thread using a Timer and PPI to trigger SAADC sampling at 100hz. Currently I have an app_timer also running at 100hz to sample the results of the SAADC (and its time...
Hi guys,
I notice that the bytes array of UUID is reversed after registerd.
For example, I define the UUID marco as follows and registe it at ble_nus_init().
#define...
I am trying to use ESB and BLE concurrently on NRF51822 SDK v11 SD130..
The BLE part is working fine but the ESB part keep causing error randomly.
I put a break-point in...
when i use C:\Users\Administrator\Desktop\nRF5_sdk14.0.0_ble_central_beacon\examples\ble_central\ble_app_multilink_central for this instance ,I debug the discover moudle callback...
The question I mentioned here
When using ble_gatts_hvx to send data, only send data pointer and length to softdevice, and softdevice did not copy these data to the softdevice...
i used pca10040_debug of bootloader_secure of nRF5_SDK_14.1.0_1dda907.
i created the key by myself.
Bootloader and zip file used the same key.
My device is in DfuTarg...
I'm using an NRF51 w/ S130 operated directly from a coin cell battery. I use the ADC with a voltage divider to successfully measure analog voltages. One of the challenges...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
NRF52832 reference design BOM did not specify the voltage rating of capacitors. What is the recommended voltage rating of capacitors?
For 32 MHz Crystal Oscillator, specified...
I'm trying to use the TWI talking to a I2C device (LED driver TLC59116). I have some working arduino code which I have converted to use on my nRF52 custom board. I'm using...
Hello,
I'm trying to measure battery voltage on nRF52832 chip using SAADC based on examples/peripheral/saadc and examples/ble_peripheral/ble_app_proximity and noticed that...
Hello Community,
I have a peripheral device which is transmitting the data through custom battery, accelerometer and temperature services.
Now I need to receive that...
