Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
We are currently working on one project.
Initially, the nRF52840 & S140 (v5.0.0-2) & SDK14.0
examples \ ble_central \ ble_app_multilink_central Based on the example...
Hi Team,
I am using sdk12.2.2 and nrf52. I want to use one gpio to detect button state & have to operation on that event.
I used one method to configure(code snippet...
Following the guide found at : file:///C:/Github/STIWHN/SDK_thingy52/thingy_sdk_v2.1.0/documentation/firmware_compile.html#compile_gcc
I still getting errors trying to...
Hello,
For the softdevice update, is it the responsibility of the bootloader to make sure, that the softdevice was copied correctly?
If for example the bootloader calls...
Hi,
When i use FreeRTOS tasks with priorities 2,3,4,5 what i need to #define for XXX_CONFIG_IRQ_PRIORITY of SPI,SAADC and GPIOTE at the file sdk_config.h
Thanks
Hello, I use nrf51822 , sdk 8.0.0, s110
I defined advertise interval and timeout
#define APP_ADV_INTERVAL 320
#define APP_ADV_TIMEOUT_IN_SECONDS 3
Also, I write...
Hey Nordic Devzone,
I am really new to Nordic and am still a student in embedded software engineering. So first some background information.
I have 6x nRF52840 and 5x...
Hello,
I am designing a custom 2layered PCB board with NRF52832 IC. I have followed the reference design given in IC's datasheet as shown in the figure. Please provide the...
Hi,
I'm currently building a BLE multi-sensors device, with mbed online IDE. I succeed in implementing BLE API, and releasing a first .hex firmware with multiple services...
Hello,
I added an extra opcode to the DFU Control Point characteristic so that I can jump to the main application by writing to it. The problem is that whenever I do that...
Hi there,
quite a beginner here and tring to figure some stuff out about the nordic programming style.
when sniffing around the given examples in the newest SDK(SES...
HI,
I got 2 nRF52840 dev kits and I'm interested in testing the long range layer (LE coded PHY ) between the 2 modules, also scan for the second module RSSI value.
I...
Hello,
This is my first time working on BLE and Nordic, so this might sound strange.
I am trying to update data on the fly when the central requests char data.
I have...
Hello,
I am designing a 2 layer board with NRF52832 IC. I am following all design considerations and reference design mentioned in IC's datasheet provided by Nordic. I have...
