Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Is it possible to setup the nrf52 with the HRS profile along with UART. I'd like to send heart rate date along with UART messages.
I'd also like to have an android app...
Hi all,
I have need to create BLE device with ability to securely store private keys and change those. According to presentation from ARM with assistance of CryptoCell and...
Hello, I wanna know where I can download it, if there is one at all?
I want both schmatic and pcb library file. I thought I can substitute and "make due" with nrf52832...
I'm using nRF52 + SDK11.0.0 + s132. I'm following this tutorial. I am able to build from the command line and from Eclipse just successfully. However, Eclipse is unable to...
Hi
I'm using nrf51822 with soft device 11.0 & want to read a 12 volt digital signal for this I'm converting 12v to 3v3 (4.5 & 1.5 Kohm Resistor) using voltage divider ckt...
I am using nrf51822 with soft device s130.I used sd_app_evt_wait() to enter the sleep mode and i disabled all the peripherals before enabling sleep mode.According to the datasheet...
I can't understand concept of control point..
Is it just one of charateristics?
So what are differences with other charateristics?
I heard that control point can...
I'm not sure if this question has been asked here before, but I couldnt find an existing answer...
I know that flash memory only has a relatively limited number of write...
What is the MDK? I am using Eclipse and GCC on Linux with the GNU ARM plugin for Eclipse. I need to upgrade from SDK12.0 to get the workaround for errata 108.
The release...
I am currently using BLE Secure DFU Bootloader on my NRF51822 256kB but my program is now too large for dual bank operation. How can I setup the Secure DFU Bootloader to use...
Hello,
I'm using SDK12.2.0.
I opened the PPI example (in SES). I want to use the GPIOTE driver to trigger GPIO tasks on Timer events. So I #include "drivers_nrf/gpiote...
Hello,
I am writing to you because I have a problem with the DVK BL652.
I ran the Quick Starter and all worked well. The DVK BL652 and UwTerminal software communicated...
i am using nrf24le1 contyroller can anyone tell me how to use the 1k sram.what is the datatype for using this and what are the compiler settings in using this.i am using keil...
Hello, recently I've been going through SDK v12.2 and board documentation but I can't find any info about choosing which of board's antenna to use.
Simply, I'd like to know...
