Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I am getting device id of peripheral on central and then getting it displayed on hypertermianl hyperterminal using ble app multilink perihperal code with multilink central...
Hi Everyone,
I have what I hope is a simple questions. I am creating a piece of hardware that will act as the peripheral to a central iOS app in regards to a standard BLE...
Is there any construction available in the SDK, to achieve printing functions, with an undefined number of parameters ? The classic example :
#ifdef CONFIG_DEBUG
#define...
Hello,
I've ready the final S130 spefication and it states that the advertiser is started as early as possible and that i runs asynchronously to all other roles. Now I...
Calling app_sched_event_put() from the NRF_RADIO_CALLBACK_SIGNAL_TYPE_START signal handler causes a crash due to the CRITICAL_REGION_ENTER() call inside of app_sched_event_put...
is there any code for device which act as master and peripheral other than nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental \app_s130_demo\pca10028...
I have a simple nRF51822 BLE application where a voltage is read by ADC periodically, and several values are sampled and averaged. However, from time to time, I get another...
Hello All ,
I am working on nrf51822 with sdk 7.1.0 and softdevice 7.1.0 .Earlier my ble connection was working very good with no disconnection anytime unless i disconnect...
Now I'm working with MCP 3.9.0.
When any device is connected, characteristic default values are not 0's. Can they be initialized in any way? It is a little bit annoying when...
Is there a separate reference resign for the 1.8V of operation (as in case of nrf51)? Or it's implicit and the chip can be powered in range of 1.7V - 3.6V.
Thank you!
I am using nrf51442 as central client.
I have used
SDK\v7.1.0\examples\ble_central\ble_app_hrs_c\pca10028\s120\arm\ble_app_hrs_c_s120_pca10028.uvproj" as a atart point...
Hi All,
I am integrating Johanson's balun and Nordic's L shaped pcb antenna, is it possible to have the antenna connected directly to the balun's pad? as in the below pcb...
The m_client_count is like instantly increased when I power up another (or the first) peripheral.
But with increasing connection interval the time till the central finally...
Hello,
i want to implement DFU with the S130. The problem is, that I currently do not use the device manager because I need both Central and Peripheral connections at the...
Hello,
This is an add-on question to the the one outlined in:
devzone.nordicsemi.com/.../
That question states that:
The maximum SoftDevice size that can be updated...
