Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
In ble events handler after connecting to peripheral device i handle BLE_GAP_EVT_CONNECTED event and try to identity connected device:
case BLE_GAP_EVT_CONNECTED:
{
...
Use "nrfjprog.exe --eraseall --programs s110_nrf51822_7.0.0_softdevice.hex --program app.hex bootloader.hex --verify --reset" to flash my device, return a error "write_and_verify_hex_file...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
As I've seen many others have done, I bought the nRF518822 Development Kit not seeing that I needed the $400 nRFgo motherboard.
Searching around reveals that shouldn't...
I am trying to get the Arduino DUE up and running with the Redbear v2 BLE shield, and SDK 0.9.3.
It was a pretty trivial operation with Arduino YUN, but I not so much for...
Hi Nordic-Team,
I've spent a while trying to figure this out but I couldn't. I need your help.
I want to load the S310 softdevice to the nRF51422 chip + the blinky example...
Hi,
I am using the ANCS experimental library and am experiencing a very strange bug.
I am requesting to attributes: APP ID and Title whenever I get a notification source...
Hello,
i have some trubble with my current power consumption. I have already read other user question and solutions but nothing works for me. To reduce the power consumption...
I have built and installed bluez 5.21 on ubuntu 14.04 witout problem (see for example this recipe ).
My nrf51822 EK dongle PC10000 is not recognized by hcitool:
hcitool...
What exactly is block size in pstorage?
Desired block size for persistent memory storage, for example, if a module has a table with 10 entries, each entry is size 64...
I'm looking into using the CMSIS RTOS on the nRF51822 with the S110 softdevice which I've used successfully with other Cortex M0 MCUs. I realize the S110 isn't well tested...
Hello,
I am new to BLE shield and arduino stuff. I am working on a project where I have to send the sensor data i.e. temperature sensor, humidity sensor and pressure sensor...
Hi,
I'm using the nRF51822 and pCA10001 as SPI slave.
For reasons beyond my control I have to read the Rx Buffer before the CSN is released.
Yes, I know I shouldn´t do...
