after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello !
You have DTM test in nRF5_SDK_17.1.0 and in nRF Connect SDK.
I have used SDK test some years ago and it looks more simple if we compare it with new environment...
Hello,
I am working with the nRF9160 to communicate via DTLS. It works, but managing certificates is a bit of a problem. I am using the AT%CMNG command.
First, certificates...
When running example code which involves BLE on nRF52840-based boards, the devices (which have assigned names in the example code) don't show up on the iOS nRF Connect scanner...
Hello,
I am using nRF Connect v2.6.0 and nrf52832 for product development.
I have implemented MCUmgr callbacks to check the DFU status, as shown in the code snippet...
I need to move everything off of UART0 so I can use it for my touchscreen
On a previous post I was told I could move everything to RTT in the overlay, but when I try to...
We've noted that our coordinator sometimes hangs and it's because that sometimes, maybe once every 1000-10000th call, the zb_zdo_mgmt_lqi_req API never responds to the callback...
We have experienced some modem faults and have implemented a custom `nrf_modem_fault_handler` to try to capture them.
We have enabled the config:
CONFIG_NRF_MODEM_LIB_ON_FAULT_APPLICATION_SPECIFIC...
Hi,
I used the reference code from inter_less8_exer3_solution and successfully built it with the nrf5340dk board. However, when building it for the nrf7002dk , I encountered...
I'm using firmware 1.3.6 and sdk 2.7 for Nordic nRF9160. For the internet connection ppp is being used.
Here are the results:
modem shell:
time wget https://leil.de...
Hi,
as i would like to use the uart shell for production purposes as well (e.g. setting the devices serial number) - how can i turn off the shell at runtime (in order to...
Hi,
I've been working on building and flashing the OpenThread CLI sample in two setups:
Setup 1 : nRF21540DK
Setup 2 : nRF52840DK + nRF21540EK
While I've managed...
I've been working on building and flashing the OpenThread CLI sample in two setups:
Setup 1 : nRF21540DK
Setup 2 : nRF52840DK + nRF21540EK
I'm using NCS v2.6.1....
Is it possible for the nRF7002 to operate in both SoftAP and STA modes simultaneously?
From my understanding of the nrfwifi driver, it seems that this functionality may...
