Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am unable to build my application for the Thingy:52 to perform FOTA over BLE. I have configured everything as outlined in the Nordic Developer Academy. FOTA over Bluetooth...
In my application I want to know if a DFU was executed successful and I'm using GPREGRET2 for it.
If a DFU as successful I'm writing GPREGRET2:
nrf_power_gpregret2_set...
Hi There,
I am trying to build a sample application (GNSS) on VS Code for my nRF9160 DK. The build used to be successful, but I noticed that it fails with the following...
Hello,
i am trying to install nRF Command-Line tools in my environment on my company's PC, i am on Windows 11 Enterprise on a Dell Precision 5820 Tower, and I am following...
I am unable to build my application for the Thingy:52 to perform FOTA over BLE. I have configured everything as outlined in the Nordic Developer Academy. FOTA over Bluetooth...
There is a lack of guidance on Blob Transfer Server/Client, so I decided to create and contribute a sample.
In Case ID: 331920, had the idea to add a BLOB Server and Client...
Hello Team,
We wanted to use a NOR Flash GD25Q32E to replace MX25R6435F which is using on the development kit. But we got an error. Please see below screen captures. ...
We are getting below error when flashing hex file in our custom board using a programmer tool but not getting the error when flashing using visual studio flash. 2024-10-15...
Hai,
We are planning to develop a Bluetooth gateway based on nrf52840.
the nrf is connected to esp32 through uart.
The duty of the nrf52840 is
1. It should receive...
Hi,
I'm using nRF Connect SDK v2.7.0 (this error happens with v2.5.0 as well). I'm trying to build the USB Mass Storage sample for FAT FS on flash, in zephyr/samples/subsys...
Hi,
I am writing to a characteristic, and I have noticed that the data is being truncated.
After establishing the connection, I performed an MTU exchange, and the MTU...
Hi
We are working on building a custom board for the nrf9161 as it's the newer chip but are having issues writing the IMEI to the device. I have flashed a modified version...
Greetings,
I have been trying to integrate file system into Winbond W25Q02 NOR storage, Initially I tested the hardware by interfacing SPI communication between nrf 5340...
Hello,
I am looking for some guidance in getting my application in a low power state. I originally came across the post here . I could not get this example working, and...
