Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi everyone,
I’m using nRF9151 with nRF Connect SDK 2.9.0. Without changing anything in overlay, prj.conf, or source code, several of my projects suddenly started failing...
Hi Nordic DevZone,
We recently acquired some Pro Micro nRF52840 Dev Boards ( link ) and were looking to use them with the nRF Connect SDK. The boards use a UF2 bootloader...
I have a question about the nRF54L15.
１．I would like to know the maximum number of devices that can be registered for whitelist and bonding.
２．I want to know how to...
I am having an issue where my nRF52840 Development Kit is not being detected by nRF Connect for Desktop , specifically in the Quick Start and Programmer apps. The DK does...
Hi, I have an Adafruit Feather nRF52840 which I'm programming using SDK 3.1.1. I want the following UART config but it is being rejected with error -134 which I believe means...
Here is a professional and technically detailed ticket template you can use to submit to Nordic Semiconductor (DevZone) , Quectel Support , or your internal System Architect...
Dear Nordic,
Could you please guide us how to set HCI_LE_Transmitter_Test / HCI_LE_Receiver_Test command?
Do we have to use Test mode command too?
Thanks.
When using the official Au Term.exe tool to perform SMP firmware updates on the nRF54L15 (NCS v3.1.0), if the tool is closed during an ongoing transfer and then reopened,...
Hello,
I previously completed a project using the nRF24LE1 chip and the nRF24LE1_24_SDK library. It was a simple 2.4 GHz two-way communication system using the basic predefined...
Hello
I am currently working with the nRF9151-DK hardware to perform tests related to PSM functionality on an NB-IoT network.
The main issue is that, although the device...
HI,
We are using the IM69D120 PDM mic for our audio application. I am able to interface the MIC and record audio with the NRF5340.
I have read the PDM data and stored...
Dear Nordic Team, Could you please help me to find the exact product which I can use to connect my two wire 0.37Wh 100mAh 3.7V 351525 Li-Po battery to the nPM1300-EK for battery...
I'm trying to combine two projects, C:\ncs\v3.1.1\zephyr\samples\subsys\nvs and BleFundamentalsL5E2 (Implement bonding and a Filter Accept List). They work fine independently...
We're developing an application using the NRF54L15. SWD will be connected to an external device that can update the firmware on the MCU if there are any issues, but we don...
