Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Context: I am making sample apps on the nRF54LM20DK ver 0.3.4 on ncs 3.2.1. I noticed that when trying to use the built in PWM shell that 100% duty cycle is not being set...
Hi,
I am working on a project that requires high quality audio capture and wireless transmission using two nRF5340-DK boards running the nRF5340 Audio application (NCS v3...
I'm sing NCS SDK 3.3.0:
https://github.com/nrfconnect/sdk-nrf/releases/tag/v3.3.0
Currently I'm using Zephyr sdk 0.17.14. I would like to start using 1.0.1 https://github...
Hello,
in our new project we need to drive a GPIO high as soon as possible after startup.
I have tried with the PRE_KERNEL_1 priority for the device driver but still takes...
Hello everyone,
I am trying to use a nrf52840 dk as an external bluetooth module on my Linux PC to be able to communicate via LE Coded Phy. I have the problem that the devices...
I have a nRF5340 module with an application built using SDK 3.2.1.
The nRF5340 is acting as a CIS Peripheral.
It has an ACL connection and a CIS connection with a Pixel...
I just realized this feature is available from NCS V3.3.0.
Does it support nRF52 series such as nRF52832 with DFU through BLE?
In this page, it seems only nRF54 are included...
Hello,
I'm using nRF9151 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). Recently I updated NCS to 3.2.2 and I started observing...
Hello, my name is dio.
I created an HCI UART application using nRF Connect for VS Code with NCS v3.2.4 and enabled the Channel Sounding component via the nRF Kconfig GUI...
I am developing a dual-mode HID device (mouse) using nRF54L15 with nRF Connect SDK v3.1.1 . The device determines its mode (BLE_mouse or ESB) at boot time via a GPIO pin ...
Hello,
I have designed a PCB with nRF54L15 SoC. Now the issue is that I have by mistake changed the MISO/MOSI pins of the device. As you can see in the following image....
Hello,
i have a custom board with a nRF52832 on it. TL:DR: i can't seem to get a connection to the chip via the SWD
When i try to recover the device it tells me the debug...
I want to flash an example firmware onto my nrf5340 board. I want to test le coded phy. So whych example should I use from the nrf sdk 2.4.0 to flash onto my device so that...
