Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello
I am using a Nrf52832 kit from Murata japan distributor.( https://wireless.murata.com/mbn52832.html)
My purpose is to be able to perform DTM on above mentioned kit...
Hello,
I am working with Window Covering cluster.
I receive command ZB_ZCL_WINDOW_COVERING_GO_TO_TILT_PERCENTAGE_CB_ID from my coordinator successfully, but I can...
Hello
I need to broadcast large amount of data on MQTT ~ 300K
I require to send it as fast as possible
how can I best calibrate settings for maximal speed send via...
i am using ble_app_uart example on nRF52833 board. I want to make a function that whenever I press button 1 on board, the board will disconnect Bluetooth connection with my...
Hello,
We are developing a BLE beacon with nRF52810 and SDK17.0.0. I modified the code on the basis of ble_app_beacon. I rewrited m_advertising.adv_modes_config.ble_adv_fast_interval...
Dear friends:
The ble advertiser device can advertising, the advertising can be monitored by a smartphone.
The ble mesh node with proxy feature also can advertising, the...
I encountered an issue where my firmware would get stuck in NRF_LOG_FLUSH();, and the same logs would be sent over RTT repeatedly. Pausing the debugger showed that the read...
Hi
My purpose:
Send 180 Bytes per 10 millisecond
I got a problem:
I use NUS project in NCS SDK15.0,when I send data per 10 ms,It return"Failed to send data over BLE...
To the kind attention of Nordic support team,
We would like our BLE nRF52 based product to reconnect as fast as possible.
My question is: are there side effects in having...
Hi,all
I want to connect my NRF52832 device with pc, then , use the value uploaded from the device to draw a curve in pc. Refer to nordic engineer's advice, i used the heart_rate_collector...
I want nRF9160 to do mqtts connection without certificate.
Modem FW:1.2.3
Here is my mqtt client_init:
When I use 9160DK, mqtts is connected normally. But when using...
Hi Everyone, I am confused in sleep modes of nrf52832. Can you please tell me the difference between System ON sleep mode and System OFF sleep mode?
also the current consumption...
Dear friend，
Based on SDK15.3, using S332 protocol stack, running on nRF52832-QFAA. Connect the device with a mobile phone via Bluetooth. The connection parameter Min connecion...
