after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi,
I have a problem with nrf5340pdk not executing the firmware. I have to build a hello_world sample from ncs v1.4.99-dev1 and I flash the development kit with the west...
I'm considering rolling back to the sdk ver 14 to avoid the nrfx vs legacy api confusion.
I plan to use only the 52810 and 52832 SoCs.
Is there any disadvantage to using...
Hi @Vidar Berg
Hope you are doing well ! i need your help regarding the beacon coded phy . I read your post
https://devzone.nordicsemi.com/f/nordic-q-a/69595/problem-with...
Hello.
Trying to compile the AES CBC MAC example out of the box, we get the ferror below.
Your help would be appreciated.
Many thanks,
Andrew
Building ‘nrf_crypto_aes_cbc_mac_pca10040...
Hello,
Updating developer machines to OSX Big Sur resulted in nrfutil failing to execute. The install via pip works correctly, but when attempting to run the binary, the...
Hi All,
We have tested the DFU(nrf52840) from a central to the target device over the BLE. In which a central device attached to the PC(x86-64bit Linux) via a Serial USB...
Hi Folks,
I am facing an issue while trying to perform a system On suspend procedure with a wake up on HITOLOW event.
No event is triggered when button pressed.
However...
I wish to develop a bare metal application (without Zephyr) on the nRF5340.
For this purpose I am unable to find the documentation how to perform Inter Processor Communication...
Hello
I used sdk v17.0 and nRF52DK.
I wrote a code that can turn on/off various functions using buttons and apps. And I don't think there's a problem up to here.
And...
We are in the process to add spectral sensor to zephyr based BLE sample, but following the tutorial to add overlay or copying other sensor configurations not helped much....
It has been said that Nordic SDK v4.1.0 for Thread is in maintenance mode. I was told that I should move new Thread development to nRF Connect SDK. I am trying to explore...
Are there any examples of libuarte enabling both uarts in the nRF52840 at the same time? I have been trying now for a full day and keep having problems with what options to...
Hi,
I have an app based on freertos_hrs example (nRF52832, SDK14.2)
I'm trying to get it into low power(sleep) mode, however the idle task keep on running and the system...
