Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello there,
I am experimenting with with the gpiote and ppi examples, and have a couple questions regarding the member variables of the nrf_drv_gpiote_in_config_t struct...
Hello,
I planned to to use in my design 1.8V. But for redusing power consumption of nrf5340, which way is correct and prefferable:
1. Use external 1.8V supply in normal...
Hello,
in file nrfx_gpiote.c there is a fatal error which overrides data because of a false array index.
nrfx_gpiote_init there is a for loop which calls the function...
Hi All:
As the topic...........,I want to set up DFU with usb,how? When I edit the USB_HID_KBD to USB_HID_GENERIC in usbd_hid_composite example,it makes some errors:
1...
Hi everyone,
I am working on the USB_MSC example and I need your advice. I read an IMU unit and I want to store the data into a file. I create a single file to store the...
I am using nRF52832 evolution board and SDK version 15.3.0 in Segger studio(Ubuntu system) for Interface LSM6DSL accelerometer using I2C.
I am use TWI peripheral example...
Hi,
I want to program a nrf52832 module and a J-link debugger is on it's way. Until then I wanted to use my Black Magic Probe to flash and debug the application. I can successfully...
Hi,
We want to choose which frequencies we should implement on nRF9160 to have the best frequency bands coverage. Would you have a list of all known frequency band used...
I want to use the sensor example to transmit 10bytes of data at at rate of 10Hz.
I have tested the publishing using periodic publishing configured with the nRF Mesh app...
Hi,
There are many undefined reference error with file nrf_atfifo.h, already checked Makefile.am is included, please help to advice if there any file is missed.
........
Hello,
I'm using the following code to communicate my NRF52-DK with pc.
But sometimes the DK transmitting repeat data and sometimes error data is sent(missing 1 byte)...
Hello,
I'm implementing libuarte with ble_app_multilink. But receiver side receive gibberish like below.
It looks like RTT message is printed to serial port. But I...
I am using nrf9160 for a monitoring project using NB-IoT network. The problem I am having is when I go to an area where there is no NB-IoT network, the device crashes often...
Hi,
We've a custom board which has NRF52832 and Maxime. They are connected over UART. ( I'm using ble_app_uart)
What I want is transfer binary data between Phone and...
Hi, i am trying to understand the SDK 17 by building my own libraries such as interrupts, ADC, IIC or so on. I was doing well untill i come across with "LOG". When i look...
