Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
hello Nordic
i am using nrf 52840 dev kit, sdk 16.0
i want to make a sampling of 2 channels at 32MHz rate. the data shell be passed to RAM via easyDMA, after every 4...
Hi, I try to change my MAC address, but return error code 8.
check error code 8 is :
So I try set the mac address after ble connected. and the function sd_ble_gap_addr_set...
I'm trying to drive LEDs using PWM on Thingy:52 and Zephyr OS. It works when I connect external diodes to GPIOs, but built-in LEDs are connected to I/O expander instead. ...
Hello,
I have an Android application that sends and receive data from a nrf52832 peripheral.
During a test for our device using a nrf52932 chip, 2.4GHZ noise is emitted...
Hi. I bought the BM832E development board and have not yet ordered the DK board.
It says that arduino uno rev 3 is compatible with it. Does this mean I can plug my arduino...
Hello,
I am using nRF52 DK development board. I'm having a problem when I load simple blink example . I am getting an error message Error: Flash Download failed -...
Hi all!
Im still new to this and I'm trying to help a friend with a PCB design. We are using the nrf52832 and recreating the design from the reference circuit given in the...
I am trying to Compiling ‘ble_advertising.c’ and get 'NRF_EVT_FLASH_OPERATION_SUCCESS' undeclared (first use in this function).
This declaretion is already in the nrf_soc...
Hi;
i tried to compile LED Button app founded in this tutorial infocenter.nordicsemi.com/index.jsp in nrf51822 pca 20006 I had these errors someone can help me please or...
I just make some change Tx power level on "ble_app_blinky" app, i see that: when change Tx power(-20, -16,.., -4, 0, 4) like this code i mark red color below.
---------...
Hi,
I was trying to load the agps sample code into thingy 91 for testing. I read the readme document which mentioned that code is compatible with thingy 91 too.
After...
Hello everyone,
I wanted to start with Thingy:91 today, so I first wanted to update the device with the newest firmware.
First thing I found confusing is: On the Getting...
Hi everyone,
I saw a lot of example in SDK (CDC ACM example, Audio example, MSC example,...) and I want to know if is possibile to modify them and use the USBW (USB WIRELESS...
nRF5_SDK_15.3.0_59ac345\examples\peripheral\twi_master_with_twis_slave.
I use NRF52810 as a slave, power consumption is 6uA.( nrf_drv_twis_enable(&m_twis);)
I see the...
Hi,
I am using nrf52832 module, sdk 17.0.2.
I have ble nus service added and device works properly had no issues till i add the AES related files and defines.
Can...
