after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Using the SDK11 bootloader, if I recompile the bootloader, package it with nrfutil 0.5.3, and perform a DFU update the original bootloader is erased but the new bootloader...
Hello,the SDk is nRF5_SDK_15.0.0_a53641a,the MCU is 52840.
I want to memory map it and refresh it .
that's 240x320 x bytes per pixel, it's 16-bit RGB, so 240x320x2 = 150k...
A manufacturer of nrf52832 module has replaced by mistake the values of C1.C2 capacitors that are connected to the 32Mhz oscillator from 12pf to 24pf and 27pf.
What will...
Hi,
I'm using NRF52 and used inbuilt UART for communication with host controller.now i need one more uart port for log printing.
so how we can achieve on NRF52?
Thanks...
Hi Nordic team,
I'm trying to run demo SPI programs from NRF5 SDK. I want to create simple SPI communication between two dongles, of which one would be master and the other...
Hi, this is my first post here, so please forgive if category/description is not complete.
I'm trying to do a quick proof of concept using ZB ZCL Tunneling. ZED is a client...
Good morning,
I'm developing an app for NRF52832 SDK 15.3, SD 132 6.1.1 with NUS service. Moreover my app has DFU and Peer Manager with LESC JustWorks security and other...
Hello All,
I am working on an indoor positioning project where I want to send/POST request RSSI values to the server/frontend. So is it possible to send RSSI values to the...
Hello,
we have a problem with a BLE connection state function. We are working with an NRF52832 device and SDK 14. The device itself works in central and peripharel mode...
Thanks in advance for any advice!
We are developing an ultra low powered network. There will be a remote control with numerous buttons. This will connect to 2-10 peripheral...
hai , I would like to program cli uart in pca10059, what are all things to change in openthread stack in order to change UART pin configure and how to compile it ? I use only...
I am trying to implement cli uart in custom board, for which there comes need for me to recompile openthread stack (in order to change UART and LED pin configuration) in GCC...
I was just working with the ble_app_uart example in nrf5_SDK_12.2.0. Minor modification were done to the main function. The build output:
linking...
._build\nrf52832_xxaa...
The site is just showing a product brief PDF, where can I access the full datasheet? Is the crystal oscillator on board or an external connection is required?
