Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Is it possible to send and receive data with the thingy91_at_client_2020-04-29_bc7ade8b?
I found, that this is not supported by AT commands, instead socket libraries for...
Hi everyone,
I have created a custom BLE service with a characteristic and I update the custom value after enabling notifications by calling the ble_cus_custom_value_update...
Hello,
I am integrating saadc example to ble_uart in order to receive analog input signals and send them via ble connection to android application. Low power consumption...
Dear Nordic Team,
We are working on connecting an I2C device to an nRF52840 Dongle . The code we are using is one we've been developing for a few weeks with an nRF52840...
Hi,
For BLE softdevice, I am wondering if it is possible to set connection supervision timeout to infinitive, which means the connection will never be considered lost? ...
Is the process of communication between QSPI and Ext. flash same for QSPI and PSRAM? If not, what could be the procedure?
And how can I communicate with 2 PSRAM using single...
Hello, I want to create a device, that can auto-connect to my phone and only my.
I thought to do it by filtering the MAC address.
But as far as I understand iPhone and...
Hi,
I was trying to find my way configure and SRAM which has QSPI interface. However some commands are different and cannot find how to modify and adapt the qspi module...
SDK 15.3.0 documentation says:
"Error codes are 32-bit unsigned integers with the most significant 16-bit reserved for identifying the module where the error occurred ....
Hi
I am currently trying to design my own custom board with just the nRF52833 SoC. I am using this for AoA and I/Q sampling. I had a few questions.
1. What is the...
A quick question. I've made an App based on the peripherals not required by the SoftDevice, in particular s112 states RTC0 and TIMER0 are used. I'm moving onto the Bluetooth...
I am able to run all samples from this folder /ncs/v1.2.0/zephyr/samples/ and see the output on the LTE Link Monitor.
However, when I try to run the GPS sample from /ncs...
Hello I notice that exemples with Softdevice ( nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b) works fine for a PCA10056 but not on a PCA10059. When I had tried to make this...
Hello,
first of all let me thank you for providing the nRF Sniffer, which is a great and very helpful tool! I use it a lot and I'm well are that one would have to pay a...
