Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi Nordic-Team, I would like to setup a testbed that should be used to measue/evaluete the power consumption of a nRF52840-DK with a connected secure element (like OPTIGA...
i am using winc1500 for wifi connections , i tried through uart too but it doesn't work . Now i want to execute thrugh spi any example or githib code is available
Hello Nordic Community,
I made custom hardware using nRF9160. I updated modem with latest firmware version 1.1.0.
After updating at_client example code my log file as...
Purchased nRF9160 DK, registered the iBasis SIM card online successfully, but can't connect the cellular network. Checked iBasis's website found the UK is not covered
https...
Hi team,
I was comparing the ble_app_hrs example from SDK v15.3.0 to SDK v16.0.0 and noticed a big difference in the average power consumption. The only change I made to...
I am testing the ble_app_blinky example on nRF52840 BLE SoC and the "nRF Blinky" Android application example which uses the Android-BLE library from NordicSemiconductor. My...
The current implementation of Mesh Config using the flash manager lack a memory listener which can cause it to never retry a store or delete operation.
Assume the following...
Dear Sir,
Could you please recomend board(hardware) that I could move my code that was developed using NRf52 SDK.
I am using ANT functionaluty and s212 software
Best...
Hi Nordic,
I had an initial project with a multilink central connecting to several peripherals through a NUS service, the system is working OK but then I added another connection...
I am using PCA10040 development board for flashing.Same it was working fine to flashing the Custom board.
Now suddenly not flashing to the custom board same board which...
I am planning to use CP2102 (USB to UART) and RF-BM-ND06 NRF52840 bluetooth module for sniffing BLE packets .
Or as an alternative for Nordic Bluetooth USB dongle.
But...
Hello, I'm pretty new to Nordic devices but I have already some experience with other ARM based devices though...
I'm playing with Timers bare metal instructions and figured...
Hi
I am currently trying to get the antenna switching working on the nRF52833 DK. I have an SPDT RF swtich which I want to use for switching between two antennas. I want...
Hi,
I've already asked this problem few days ago, but I couldn't figure out the clear answer.
The above figure shows the VDD values of BLE chip. The power supplied...
