HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
I defined an integer value _ALIGN(4) uint8_t sixteen = 16 and assigned sixteen to a FDS record that is later assigned to the p_data of a custom characteristic. However, when...
I updated to v10.3.0 of the nrfjprog and mergehex tools and I've noticed that the behavior of the page erase command takes far less time when it gets to a certain region of...
Dear All,
I am trying to interface my nRF9160 sensor with the LIS3DH accelerometer.
What I have done so far are the following:
I am trying to use I2C_2
In my prj...
Hello Nordic Support,
I am using nRF9160-DK with the latest module firmware: 1.0.1, board version 0.8.3
I followed the instruction and it only works for tag v0.4.0, I...
Hi devzone!
I connected my flame detector sensor(szh-ek086) which sends data analog value to my nrf52840 DK.
To receive the analog value from sensor I used saadc module...
Hello, I'm trying to set up a series of remote scripts to test functionality on my hardware. The idea being that I can run a handler on the Nordic device and then control...
Hi,
is it possible to read/write the MX25R6435F external SPI NOR flash using Indirect Mode ( https://wiki.segger.com/Programming_External_SPI_Flashes) with Segger JLink...
Dear,
I am doing some range tests with the nRF52840 and saw that the RSSI value of the PCA10059 (USB dongle) can be more than 10dB lower than the one of the PCA10056 ...
Hello everyone, I am trying to implement a blocking wait using the app_timer.
To do this, I am starting a one-shot timer whose callback function sets an initially false...
Maximum current consumption for each of the pins in the respective modules of PWM, TWI-I2C, TWIM-I2C, TWIS-I2C, SAADC, UART, SPIM, TIMER, RADIO-2.4GHz under the operating...
Hi,
I'm trying to run the gps application off the master branch on the thingy91 and it dies like this:
It's built using the Nordic SES on windows.
Any ideas? ...
Hi all,
I am trying to connect to device with specific UUID. I am not sure what have I managed to do, below are some logs from NRF Log.
Did I connect properly?
I am...
Hello,
I am trying to run the mbdedtls example of random number generator shown here https://tls.mbed.org/kb/how-to/add-a-random-generator
I added MBEDTLS_CONFIG_FILE...
when i change the baud rate to 115200 my uart (Rx and TX) are giving me garbage out put.
so what do i need to change in my code(ble_app_uart example) when i have plan...
