after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I can use the SPI master functionality within nrf_drv_spi.c/.h just fine (i.e. calls from main) until I connect to my nRF52840 and utilize NUS. If I try to issue a nrf_drv_spi_transfer...
Hello,
I am working to implement the BLE stack for a HID keyboard, borrowing/based off the supplied example "ble_peripheral/ble_app_hids_keyboard".
Stack initialization...
In SEGGER Embedded Studio I am not able to connect to the J-Link anymore.
The error message says No idcode detected.
The J-Link commander program returns the following...
The SysTick port for NRF52 does not support tickless idle on freeRTOS, what is the reason for this limitation? Are there any known problems behind this limitation?
I tested the code below to make the board go to sleep and wake up on each button press. When I start, it draws 30ua, but when I press the button it shoots up to 200ua (a clear...
Hi,
We are developing nrf9160 sensor based product powered by primary battery(non rechargeable). Sensor current consumption is less than 1 mA.
while trying Saft LS14500...
Hello,
How can i put out the received Adv Data on the UART? Currently I get for every advertise packet the BLE_GAP_EVT_ADV_REPORT in my ble_stack_handler. Then i wanted...
I'm using the ble_app_hrs example code and added a new custom services with multiple characteristics . conn.interval 10ms- 15ms and need to get maximum throughput so i set...
I have nRF52840 DK (board PCA10056) . Right now I flashed LED blinking program on nRF52840 DK. It is fine.
Now I want do ADC operation, so I fed some external analog signals...
Hello, I am trying to send and recieve data with the M24C32-FMN6TP 32 Kbit (4K x 8bit) eeprom. My data are arrays with 16bit values and the datasheet says it cannot write...
Hi,
I have nrf9160 dev board.
It seems to me that getaddrinfo() has memory leak. If socket is closed, and call getaddrinfo() to reopen, it returns -10 (memory) error....
i'm looking for support in desinging modules working in zigbee network with driving this network from mobile phone by bluetooth. It has to be multiprotocol system. How should...
Hi,
I was trying to load the sample example code for Assets tracker in SEGGER Embedded Studio for ARM V4.20a but i encountered with some error.
Transcript & Output:- ...
Hi everyone. I've implemented kind of simple FW updater. The purpose is to copy FW from flash (0x0 address, no MBR or SoftDevice) to RAM buffer on node1. than send this FW...
