Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
I am using
nordic nrf52 SDK version : v15.2.0
Freertos version : V10.0.1
The system has hardware timer which runs at 6.4KHz. For every 1.6 KHz, from timercallback...
Hi
AfterI updated the nrf_Connect v2.02 IOS version. I found that disconnect will happen when key in the bonding code "123456".
And my code never has this issus with previous...
Hello to all,
I am using nRF52840 DK with SDK15.0 and SES. To communicate with MS5540C I have used SPI master sample example but getting some incorrect results.
Almost...
I get a lot of error after just adding usbd source code into makefile. error: unknown type name 'NRF_USBD_Type', error: 'USBD_INTEN_ENDISOIN_Msk' undeclared here (not in a...
Hi, I am new to Nordic. We are using NRF51822 chip with S120 version of softdevice. Recently we made few changes in SDK code running on nRF51 controller chip. Is there any...
Hi, I'm using the 15.3 SDK ble_app_beacon example and want to add scan response data.
I've found some examples in the devzone, but not matching the example code in this...
Hello,
I'm currently using the nRF52840 DK and i need some help. On the other hand, i have BLE ela identifiers/sensors : elainnovation.com/bluetooth-low-energy.html
My...
I have nRF52832 running ble_app_rscs as a server, sending notification to the client every hour. I know that the client can read the values also by sending bt_gatt_read to...
dear Devzone
A disconnect error 0x22 occurred.
I know that error 0x22 is LMP_RESPONSE_TIMEOUT / LL_RESPONSE_TIMEOUT.
However, the location of the error and the reason...
I am using nRF52832 with SDK 15.2.0 for my application. The application is created taking ble_app_uart example as the base. I have modified the example to suit my requirements...
Dear,
I am working with thingy:91, v1.0.0, and running asset_tracker, I got fix location from GPS, but I am not so happy with these positions from thingy:91, sometimes the...
It seems that when I call nrf_inbuilt_key_exists() to determine if a certificate already exists, it causes a subsequent nrf_inbuilt_key_write() call to either fail or succeed...
Hi,
We are using a custom board based on nRF 52840, trying to transfer data to external QSPI flash(GD2QC).
Flash was successfully initialized and exchanged chunks of data...
Hello guys, i am trying to write a c code to read and write data to the onboard memory. i am using nrf52840 and segger embedded studio. i have used sio pins 41, 40, 04, 44...
Hi,
I already tried connecting my nRF9160 (in July) without success. I'm trying again but still no luck. If I'm right Orange has LTE-M already rolled-out in Belgium?
Anyone...
