after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Below is a picture of advertising event current waveform:
The TWI current consumption is upto 2mA, I change the peripheral from TWIM to TWI, the current is exactly the...
We are developping an application using an NRF52840, Based on nRF5 SDK for Thread and Zigbee V3.0.0
Running S140 softdevice
We are using BLE advertizements and Openthread...
I have a custom board with nRF52840 and uses Segger EDE.
In our project we would like to store some info about production to flash memory (DeviceID, production date etc...
I followed the guide Configuring and performing DFU over Mesh ,old firmware was examples\dfu\build\dfu_nrf52832_xxAA_s132_6.1.1_Debug\dfu_nrf52832_xxAA_s132_6.1.1.hex,new...
Hello,
I want am use NRF2401L01 for sending data wirelessly from one device to another device and vise-versa.
The First device is arduino nano(Transmitter) which senses...
I looked at the following question
nrRF2 GATT attribute read callback
and it does not quite answer what I want to know.
What I need to know is do I get signaled by the...
I have followed the getting started, with my new nRF52840DK, with switches at:
Sw6 Default
Sw8 On
VDD selected
when plugged into the USB, LED 5 blinks rapidly, LED...
Hello.
In order to connect multiple units on the previous question page ( https://devzone.nordicsemi.com/f/nordic-q-a/51970/implementing-multilinks-on-multiroll-programs...
I want to develop our PC software to control the USB nRF52840 Dongle to be as a BLE central device，so I need to know the command that the nRF Connect used to do this，but I...
HI as i am new to nrf nordic semiconductor development i have some quetsions regarding application im developing
I am trying to develop Ble application where nRF 52 will...
Hi,
I am trying to add DFU service in ble_beacon example. I am using SDK14 and softdevice is S132_5.0.0 for 52-dk.
I have merged dfu example with ble_beacon and initiate...
Hi,
For my application using softdevice I need ADC update every 400ms and Battery level update every 2sec and string update for HT1632 led driver every 2sec.So I have created...
Starting with the BLE Uart Service example code, I wanted to send longer length packets, so the necessitated modifying settings like NRF_SDH_BLE_GATT_MAX_MTU_SIZE, NRF_SDH_BLE_GAP_DATA_LENGTH...
