after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
We are currently developing a Sensors/USB/BLE/LTE-M1 product for a customer. The board is equipped with one nRF9160,for cloud communication, and one nRF52840, with a...
Hello, I am using nrf5832 with SDK 15.3.0. I want to filter peripheral device based on mac address. I modified example code "\examples\ble_central\ble_app_blinky_c\pca10040...
I'm facing problem when I want to stop receive task, event EVENT_RXTO came at long time period. 4 to 5 baudrate bytes.
Is trere any documentation where could read time between...
Hello,
I want to develop a data transfer service which has a control characteristic that is used to write commands on the phone app and if the command matches any command...
In our application we have made a connection between two nrf52840 devices. with softdevice 6.1.1
normally we operate in 1Mbit mode and tx power on 8.
if we change from...
Hi,
After sending a few textmessages from the client to a server (8 bytes long approx. 10 messages/sec) i get a mesh assert on the client sometimes:
0> <t: 205648>, app_error_weak...
Hi, I'm using a PCA10056 DK board to start new development. I try to program DFU secure bootloader and SoftDevice using nRF Connect 3.0.0 My issue: - configure both hex files...
Hi All
I am recently working on CSAs (Channel Selection Algorithms) in BLE on nRF52840DK, and I am using Zephyr to develop them. I have 3 nRF52840DK, one as sniffer, the...
Hello, I've developed a BLE Mesh Network using the NRF MESH 3.1.0 SDK and the nR5F SDK 15.2.0. My network has 1 client node and max 63 server nodes: I'm using the generic...
I've been developing a solution that utilizes Mesh DFU along with the Mesh Bootloader. However, I've been seeing a frequent issue where the DFU aborts prematurely due to missing...
Dear DevZone,
I'm trying to use the Seeed CAN BUS Shield V2.0 (MCP2515) with the nRF52840 DK, but the library provided is written for Arduino One.
Do you know if any already...
Hello.
I m looking for libraries wich contains functions/methods (for example how to scan, provision, adding nodes etc. ) and solution how to use them.
I found something...
I am working with nRF 52832 platform and I soldered SB12 and cut SB10 because I wanted to feed from the external power supply and with this situation I can not connect to...
I have been working with the Nrf52840, SDK15.2 and Segger Embedded Studio 4.20a using external GNU 7 2017-q4-major. The project builds without error on the original PC. I...
