Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
The NRF_MODULE_ENABLED macro does not play well with Eclipse. I've tried enabling all Modules in the Symbols section of Eclipse but still it does not enable any module utlizing...
Hello all,
Anybody knows "EVENT_STARTED does not fire" issue will be fix or not?
I really do want to use the PPI function at Tacq=3us.
When can I get the counter measure...
Hi,
I am trying to use EasyDMA. Is it preferable to use with ...\peripheral\uart or ... \peripheral\serial. With ...\peripheral\uart there are lot of errors. I tried with...
In the code above I get an error that nrdx_gpiote_in_init() and nrfx_gpiote_in_event_enable() are undefined.
In CMSIS configuration wizard -> nRF_Drivers i've enabled...
Hello everyone, i work on nRF24L01 and i have 3 ardunio with 3 nRF24L01 and 3 IMU as transmitter and 1 ardunio with 1 nRF24L01 as reciever, i am trying to recieve data from...
I have migrated a project that uses Thread DFU from SDK for Thread and Zigbee 1.0.0 to 2.0.0.
I have successfully loaded the new MBR, bootloader, settings and program via...
Not sure where the problem is. Some of my boards, the microphone works fine, on others it doesn't. I am using a Knowles SPK0641HT4H-1 PDM microphone. I am using it as mono...
Hi,
I am experiencing an error of up to 8% on SAADC readings on the NRF52832. We have performed a sweep of the full range of the ADC and produced the following graph which...
Hi
My application requires that SPI CS is NOT TOGGLED within a transaction, only at either side
My Transaction consists of:
1 - Slave sets up buffer ready for Rx and...
we are entertaining the idea of using an nRF52840 with a Semtech SX1276 (or possibly SX1262) as a BLE/LoRa endpoint node. We believe this is doable but wanted to make sure...
Hello, I am using SDK15.2 on nrf52 DK with SD 6.1.0 and having an issue while sending back to back data using NUS service. I have edited the ble_app_uart application and trying...
So I am brand new at this product line, and basically new at C in general, I come from VB land. So bare with me please
I purchased both a Nordic nrf52 dev kit evaluation...
Hello there,
I'm sending IMU data (16bytes) using a notification from a custom board to a phone. My final goal is to send this packet of data (16 bytes) every 10 milliseconds...
