Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello.
I try to make audio noise meter on nRF52832. I used analog MEMS MIC with OPA which I turn on via MOSFET while before measurement. I'm using SAADC triggering by RTC...
Hi there,
What changes should I have to do to the light switch example to provisioning the client and server using group address instead of unicast address?
I believe...
In our application we need to have the NFC pins configured for GPIO and APPROTECT enabled.
As an additional safety feature I verify the UICR content inside my application...
Or any general how-to documents when the users want to set up any peripheral using the direct register access? I try not to use SDK for simplify and minimize the code side...
Hello,
I'm trying to implement the Gazell protocol for one of my tasks. I understand there is CRC for the data sent from the device to the host. I cannot however find anywhere...
Dear Sir
I'd like to develop the Window APP for Mesh (like nRF Mesh).
And I've face a problem. The ECDHSecret key of the Windows side didn't match the device side(Thingy...
Hi everybody!
I am new to programming with Nordic SDK and have some questions regarding writing applications with secure and buttonless DFU via BLE.
I have looked through...
I am using NRF52840DK with SDK15.2 to test the DFU.
I use Segger Embedded Studio to compile both the secure_bootloader project and ble_app_buttonless_dfu project.
Then...
Hello,
Is there any development board like an Arduino mini for the nrF52840. It need to fit a in very small enclosure
Ideally, I would like to test/develop some sensors...
Hi,
I am working with hid keyboard example on my Windows machine.
Problem 1 : After flashing the code, I make bluetooth connection and the code works properly. Then I...
Hi,
I am reading the Product Specification v1.3 of the nRF52832 SoC.
On page 23 the RAM0 block section 1 address is given as 0x21001000.
From the context I believe, this...
As per one of my discussions with , on another thread here , I can send a GenericOnOffGet from my android activity and I will get the status of the light in GenericOnOffStatus...
Again!!! I have a lot of problems to navigate on the Nordic products.
I follow the links and went to the start52840dongle and downloaded the SDK.
I find only stuff regarding...
Hi,
In looking down the road for product enhancements and migration to the 5.0 Bluetooth specification. I am interested and wondering if any discussion about chipset production...
