Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
As well know, the max packet length is 252 byte in nRF51822 proprietary protocol.
Would you please tell me how to send / receive 252 byte packet? Where can I found...
Once written, you can not write it for the second time. It will not cause an error, but is there any way? Write the source code below.
NRF_FSTORAGE_DEF (nrf_fstorage_t fstorage...
Hi guys,
I'm adding my own 'hello world' model to the example on element 0.
For this i've implemented a simple model;
Client sends 'Set Unreliable' with char[20] value...
Hi guys long time I hope things go well there
so.. as the title says, sd_ble_gattc_write is returning error 19 "randomly" I am trying to transmit data chunks from my central...
I'm developing HID device using HID generic class. Device is required to change polling rate at startup. In SDK 14.2 this was done through modifying bInterval in descriptor...
HI. I used a translator.
I am using the nRF52840 DK and SDK15.
I want to save power when there is no input from the switch.
I want to wake up when a switch input ...
Hello together,
I have a strange problem and don't know how to proceed...
At my customer-specific electronic a Kionix KX224 is placed next to the BLE module which contains...
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh.
I based my development on the Light Switch...
It would be very helpful to hear of others experiences getting these licenses, also I would like to find out if anyone has any advice of anything to be included or excluded...
Hi,
I am currently implementing the protocol for a serial DFU, following the instructions given here:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hi all!
TL;DR
Is there a way to start 2 timers in 1 instructions ? (or to synchronize them afterward?)
- - -
Background
I need to take 8 timestamps of GPIO edges...
Hi,
I'm using S112 v6.0 with SDK 15.0 on nRF52810. It's based on app_ble_uart example. I have some data to save in flash. I define the address as follow:
#define PAGRE_TO_ERASE...
I want to extend the Thread Cloud Client Example (thread_cloud_coap_client_pca10056) with a peripheral controller. And I am looking at the UART Example (ble_app_uart_pca10056_s140...
Hi,
I will connect nRF52840 with other BLE module (ESP32) and they must exchange data (at first aproximation 20-50 bytes each 1-5 seconds).
I need to acheive lowest power...
