Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi everyone!
I'm new to this platform and researching if it's right for my game studio. What I am looking for is a list of boards that have compliance, ideally in the EU...
Hello!
SDK15's DFU with app_scheduler is great!
I am able to Select, Create, and Write an Init Packet. On Execute, however, I get "Flash erase failed (0x3)". What might...
Dear All: My board will reset some time, and i print the register "RESETREAS", and It's value is 8, the PS says it is "cpu lock up detected", Could anyone tell me what will...
Continuous input of audio stream at ATX , but intermittent output audio streams at ARX. why?
how can i use data channal? Once data (three bytes) is sent at ATX,Receive data...
I try to use the SDK 11.0 for my nrf52832 dfu function . But i encountered the error as below:
I am using the ANT_s332_nrf52_5.0.0 .
Any advice . thanks
Building configuration...
Hi all,
I am using SDK14.1.0
Steps of my execution are -
1) My requirement is to make bond when making connection to the android APP. I have done following initialization...
I'm just getting started with the NRF52DK, Mbed and BLE development. I started with the BLE LED demo( https://github.com/ARMmbed/mbed-os-example-ble/tree/master/BLE_LED )...
Hi, we're developing a peripheral (SD 132) which uses whitelist to prevent connection from unwanted devices.
All works fine and when an unlisted device try to connect, it...
I'm running the code as shown in FDS Usage here: http://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v14.2.0/lib_fds_usage.html?cp=4_0_0_3_50_3
The FDS_EVT_INIT...
The short to suspend after last RX is documented in innocenter, but not defined in the nRF5 SDK (rf52840_bitfields.h). Other bit definitions, such as TWIM_SHORTS_LASTTX_SUSPEND...
Hi,
Is there a "stand alone" DFU updater which can be given to end user not as part as NRF tools apk?
We would like to give end user the option to update, but as simple...
Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
I have a working application based on one of the examples in the dev kit. It was quite a struggle, and shouldn't be that hard. I would have expected simply a table of variables...
Hi There
I am developing a custom board on NRF51822. I have a noticed that the chip is getting stuck every day and to run it again I need to press a button on/off to reset...
