Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi, I'm trying to create subfolders with loop. My partly code looks like:
So, it creates new dir but after that my app is crashing and rebooting, and it works fine if...
Hi, I have been running into some problems with the serial secure bootloader example in the SDKv13.1.
I build the example project from the SDK v13.1 with a custom generated...
Hi, I'm new to the nRF52840 PDK and using it for some evaluation purpose for a specific product.
Would you mind telling me how to debug the board? Is it just plug in the...
Hello,
I am developing a new application for Asset Tracking, whose general architecture is the common one - where Beacons are mounted on asset and the Reader scan for Advertisement...
Hello Everyone,
I am working on nRF52832 based custom board and testing the BLE advertising and connection with custom board, custom board adverting but when I am going...
Hi, Nordic staff.
I'm working with Central device using S120.
Our custom has developed a peripheral device using third party's BLE module and
wants the Central device...
I am trying to initialize the BLE NUS UART service and the BLE LBS service so both can be used at the same time in a single nRF52 application. I can initialize a single service...
Hey,
I was reading about nRF5 IoT SDK and it all looks amazing, I am really shocked. There is only one bottleneck I can see right now and I am not sure if there are any...
nRF_log_1.8.1.txt Hello Nordic Support Team,
We are trying to run the OTA DFU on the nRF51 device via the nRF Connect iOS application V1.7.5.
The DFU Device is available...
Hi,
I'm trying to evaluate the IAR simulator, and I'm using it w/ nRF52 samples. Besides getting errors due to the errata and system init, I'm not sure what are the use...
Hello, I was wondering if it was possible to simulate the nRF52 board using the simulator in Keil. I am trying to use it as a SPI master and it would help to be able to simulate...
In our application we use gazell. We also want to use the flash data storage which uses softdevice.
With gazell enabled, we cannot access flash.
What is the recommended...
Hardware: nRF52 DK
Example: ble_app_hrs
I have a problem with starting program using debugger. I starts debugging session and starts program using resume button, breakpoints...
I'm trying to configure SWO properly, specifically to get the output in Eclipse. The following code is used to initialise the SWO.
I have a snippet that outputs a string...
