Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I am working with nRF52832 and SD 132 and SDK 11 (nRF5_SDK_11.0.0-2.alpha_bc3f6a0).
One of my BLE services has a characteristic with an attribute larger than 22 bytes. It...
i was working with a nrf51822 module.after about 50 that i programmed the chip with my jlink programmer (some time i program it with stlink V2) it be damaged and not worked...
I am designing a BLE device. Want to make the PCB as small as possible. to download the code/debug etc I need the a connecter on the board which can connect to the nrf52 preview...
Please excuse my ignorance, My company is designing in the nRF52832 for our first product using both ANT and BLE. From looking at the documentation on thisisant.com there...
I've got a strange problem with updating my Magnet-Characteristic.
I use a service with 4 characteristics (Gyro, Acc, Mag and Temp Values) and update them on a timer base...
Hello,
Two issues want to ask, after tried the BLE_NUS example code.
From other posts, still does not exist clear solution (example, pictures) ?
Sure has an application...
Hello,
I am working with the uart module. While configuring the uart I encounter 2 issues.
First when in the uart_init function the pin for uart output is configured...
Hi,
I am using nrf51822(128k), SD 6.0, SDK 5.2.
I found that nrf uart v2.0 app will add a "0x0A" at the end of data that I want to send.
How can I remove this?
Thank...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
I've never used Gnu's GCC before, but after 20 hours of trying and failing to install it on my macbook, I'm finding a shining hatred. I've downloaded their exhaustive list...
I migrated to nrf52 and countering some problems.
I am trying to sample 4 pins every 2ms with SAADC.
I started with Example here .
I simply changed
uint32_t ticks...
I've got a gyro I want to read some data from, but I don't know the values and can't verify if they got read correctly. When does nrf_drv_spi_transfer start to read?
i...
Hi, i;m trying to build the "nrf52-ble-app-lbs" example which i downloaded from git hub github.com/NordicSemiconducto....
I followed the instructions in the README file...
I'm thinking about changing ADC resolution during operation.
What I want to do is:
start
・Operate in 8bit ADC(normal time)
↓
・Operate in 10bit ADC(particular...
