Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I've been trying to get SPI slave running on the NRF54L15-DK for over a week. I am new to Connect SDK but have successfully completed this task with NRF52840-DK (and dongle...
I changed the file, C:\Users\kruenheck\AppData\Roaming\nrfconnect-bluetooth-low-energy\uuid_definitions.json so that it has a new service:
{ "_comment": { "comment": [ ...
I am programming with nrf52833,ncs v2.9.0.Based on peripheral_hid_keyboard and cetral hid.
I send about 6k hid keys to central via ,while sending,peripheral side
But ERR...
Hi Nordic team,
I’m trying to use my nRF9151 DK as a Bluetooth Host (Zephyr) connected over UART (H:4) to an external Seeed XIAO BLE board (acting as the Controller). My...
Hi,
We have functioning application code under the 2.4.4 SDK development setup. I would like to start migrating to newer code but am encountering issues. (Ultimately, I...
I have an nRF5340 DK (not audio DK), and I want to send LE audio from my LE audio compatible device to my DK and then have my DK play that audio over I2S to my external amp...
Hi there, I-m trying to compile a hello world sample with an encrypted bootloader
# Sysbuild configuration file.
#see C:\D\dev\nordicsemi\v2.7.0\nrf\doc\nrf\releases_and_maturity...
Hi all,
I'm currently facing the issue that we are receiving a PKCS7 encoded response from our EST server via a `/simpleenroll` request.
The PKCS7 response now has to...
We have a locator-beacon setup based on this https://docs.nordicsemi.com/bundle/ncs-2.9.1/page/nrf/samples/bluetooth/direction_finding_connectionless_tx/README.html running...
I have been facing a persistent Zephyr CMake/Kconfig build failure in my nRF Connect SDK setup.
Environment: Windows, nRF Connect SDK v2.7.0 , Toolchain v2.7.0 , using VS...
Hello Nordic team,
we are using a nRF52820 module in a beacon. After flashing the firmware and connecting via nRF Connect for Mobile, we can read the Service and Characteristic...
Hi,
I'm trying to CONFIG_MCUBOOT_ACTION_HOOKS with mcuboot on a custom board build with an nRF9151. McuBoot works well, but I'd like to use CONFIG_MCUBOOT_ACTION_HOOKS to...
Hi
I use MT8852BE to test nRF54L15-DK ,TX power setting 8dBm but MT8852BE Power(Pavg) show -6.07dBm ,Why is there such a discrepancy in the values?
nRF54L15-DK Setting...
For power cost down, use dts config to set pwm gpio H0D1 as follow:
pwm1_default: pwm1_default { group1 { psels = <NRF_PSEL(PWM_OUT1, 0, 26)>; nordic,drive-mode = <NRF_DRIVE_H0D1...
