Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I am using nRF52840 S140v7.0.1 and we are going for certification. I am bit confused with Bluetooth core version mentioned in Nordic certification and website....
hello Support team,
with asset tracker examples, seems not able to connect to nrfcloud recently with NB-IOT network.
do you know what is the reason?
Best Regards...
Hello,
I open the project :
I want to flash the basic application asset_tracker to my Thingy 91 after I built it from Segger to be sure everything is set and working...
Hi i was trying to add nrf calender part which i found in git hub for nrf52 chip with ble app uart example, but when i nrf_sdh_enable_request() called to initialize ble system...
Hello
I want to install the nRF Connect SDK (v3.4.1) on my Linux Elementary OS 5.1.6 Hera to use the nRF9160 and the Thingy91 later on. I've installed the toolchain and...
Hey,
I am working on S130, nRF51, been working for a long time with DFU and it was fine both using nRF Connect and nRF Toolbox
Lately I changed my workstation and so...
Hello everyone I am trying to program my dongle with the Dk Following this schematic :
When I press the reset button on the dongle, the led start pulsing in red.
I am...
someone that can give me a datasheet of this microcontroller (i think) i searched the hole web and don't find one in specific, the one i found are different in the last line...
Hello, I am working on low power modes of MCU M33 core in nRF9160 SOC.
From the document of nRF9160 product specification v1.0, understood that there are two low power modes...
Hello,
I am trying to capture the advertisements of the surrounding BLE devices with NRF52840 Dongle using pc_ble_driver_py python library. I am successful in capturing...
I am working on third party module RAYTAC MDBT50Q-DB with nRF52840 with SDK V17.0. I am trying to run ble_app_interactive example on it but just can't get it done. I have...
Hello,
I'm using the light_switch example for my application and I've integrated my custom model into it. I want to learn which address the server and client respond/publishes...
Hello,
I want to give user defined hard-coded OOB Number in this example for generic on-off Client-Server code, for provisioning both client and server node ( nrf52 DK ...
