Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
My nrf 52840 pdk and my custom pcb with nrf 52840 soc. both are running with same application ble_proximity example from sdk 14.1 and softdevice s140 5.0. when i set...
Hello All,
Chip : nrf52832
Mobile App : BLE scanner
Requirement : We want to transfer 20 Bytes(or more) at every 8 ms. Is it possible?
I have tested it :
No of Bytes...
Hi all i am facing few problem after checking the power consumption of the nRF52832 using the Power profiler kit. I followed the demo video in the link ( https://www.nordicsemi...
Could you please check whether 52840 can support memory map to QSPI PSRAM on QSPI interface?
If yes, that means the compiler would see a big RAM space of 2~8MB QSPI PSRAM...
hello，all
NRF_RADIO->CRCCNF
NRF_RADIO->CRCPOLY
NRF_RADIO->CRCINIT
If the register setting are different, can rx device recieve the message from tx device? whether...
Hi,
I use the peripheral ble_app_uart with nRF52832 (Murata module). The nRF52832 is connected to another MCU, STM32L476, via UART.
I develop using IAR, with SDK V15.0...
Hi All,
Enter to Direct Test Mode, the nRF52832 will transmit 2426MHz channel frequnicy only when set any different frequency channels (e.g. 2402MHz, 2418MHz) in the Tx...
Hello,
I don't understand why the ble_advdata_short_name_find function never return a true value. I'm sure that I send a short name because I verified this on the nRF connect...
Hello, I want to synchronize several peripherals with a central, I already tried to do it with the state of the gpiote but I did not have the expected result at the level...
Hi
I'm facing a Hard fault on the softdevice when trying to call sd_ble_gattc_write(). SDK15, SD140
I have a Multilink central connected to UART using app_uart. when a...
I have been doing a bit of searching and reading but I'm none the wiser.
I have a client that uses lots of BLE nRF51822 based modules made by Raytac Corporation in a classroom...
I am converting Arduino BNO080 library ( github.com/.../SparkFun_BNO080_Arduino_Library) to nRF52832.
Specifically, this is a function for sending a SHTP packet over I2C...
hi to all,
i had developed a device with NRF51822 wih S130 and i want to port my application to new NRF52840 soc S140 and SDK15, S130 has an structure that let me to limit...
Below are the symptoms, but it turns out the problem was quite simple: the device is not seem capable of scanning while at the same time being connected, unless you use a...
Hello,
I have a problem where the nRF52840 is not advertising. The code runs in the debugger but there is no radio signal. I've already sent the schematic and layout....
