Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Helo, Im trying to sending data from sensor between two nrf52832, SDK 15.0.0 SoftDevice S140 on both. Im using uart central and peripheral examples on transmiter and receiver...
Hello,
Like in the description, I dont get this to work. Im trying to get The nRF24L01+ connected to a PIC16LF18345. I did Some Pictures of the SPI logic and Here is a Part...
I have the nRF52840 PDK and tried to download the firmware as per step 7 to paste it to the JLINK folder to make LED1 blink so i can test NFC but cannot get led 1 to blin...
I was wondering if adding a capacitor in parallel with the coin cell battery would help with the battery life by smoothing out the peaks. The scenario shown in the chart is...
Hello All,
I have successfully built the secure_bootloader app. I have the bootloader working with the button. I can upload application files using DFU. I tried the buttonless...
Hello
I'm currently running ble_app_uart__saadc_timer_driven__scan_mode and would like to modify it for faster sampling rate. However, NRF_ERROR_RESOURCE presents an obstacle...
Very new still learning.
I am using Keil and trying to setup the tools>customize tools menu.
Following the tutorial I am able to create the eraseall macro. No problem...
Hello~!
I am working on modifucation code of ble_app_uart example.
nRF51822
(SDK12.3.0_d7731ad)
Softdevice 130 (v2.0)
I know the original UUIDs are provided from...
Hi, I am working with the example Blinky_freertos present on the SDK_13.0.0_04a0bfd.
I have built the example w/o issues in compilation but I have the following problems...
Hi i get this error when compiling. (version 0.9.7)
I'm using arduino DUE and BLE Shield (redbearlab).
I get the error: EEPROM.h: No such file or directory in bootloader_setup...
I tried building ' pca10040 ' configuration of " nrf52-mpu-easydma-using-gpiote-and-registers " example from " https://github.com/Martinsbl/nrf5-mpu-examples ". The following...
Hi
I am working on nRF51-DK with Mbed IDE & used PWM example code from link : https://os.mbed.com/handbook/PwmOut
When enabled PwmOut, PWM signal is observed on the oscilloscope...
I would like advice on whether the following is a valid ble transaction.
We have a product with the nrf52 in it running sdk 12 and softdevice 3.0. This is setup as a a peripheral...
