Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I'm developing nRF51 proximity based device using nRF51822 that acts as BLE peripheral. It advertises continuously using connectable indirect mode.
User has Android...
app: nrf tool uart on iphone 5s
sdk: v8.1.0
softdevice: s110
example: ble_app_uart.
i have modify it based on the answer :
link text
my advertsing init as...
The device I completed has similar RSSI values at approximately zero distance as my development kit; starting with default Tx of 0dBm from the nRF51822 I achieve approximately...
I am having an issue implementing a WS2812b driver for the nrf51422 using the 210 softdevice. We currently have ANT enabled with a tx master only channel setup. The WS2812b...
What I would like to do is run a basic SPI program that reads data from a register on a non Nordic transceiver chip. My nRF51 would have to act as the master because the transceiver...
Hi,
Which service should I use for temperature non-health related, like room temperature, for example? I have browsed trough the Gatt Specification>Services of the Bluetooth...
Hello,
I follow the tutorial devzone.nordicsemi.com/.../
And in the step of copy examples
I only got ble_app_uart_s130_pca10028
and no package of s110 was found
I'm...
Per my another question:
devzone.nordicsemi.com/.../
I have taken the kind advice of Bjørn Spockeli but to no avail.
I tried this solution to enter debug mode:
...
I want to use the sd_ble_gatts_hvx() to send the notification with a packet, and the length of packet is 12 bytes, but the return value is "0x000C". I tested the length and...
Hi,
I try to run a dual mode(peripheral/central) with S130. I'm using SPI serialization and sending command form an external MCU. I try to follow the example ble_app_hrs_rscs_relay...
Hii all,
I am trying to work with dfu, I developing an application that works with dfu, when I flash the softdevice and bootloader the device advertising as dfutarg and then...
I've loaded the S210_nRF51422_5.0.0 softdevice on my board from the nRFgoStudio.
I compiled the ant_hrm_tx_auto_s210_pca10028 project with no problem. However, when I try...
Hello,
I am developing two systems. One is a peripheral that advertises both a beacon and a ble peripheral custom service (using nRF51822 with s110 softdevice). The second...
Hi,
I am trying to use an nrf51822 with a sensor that outputs value between 0-5V. What I am confused about is how to read input voltage on the beacon. I saw some people...
Hi,
I need to debug my perpheral device, but as I know if I do debug when SD is running, it can cuase the time sync issue, then cause the hard-fault. I know there's a way...
