I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
I'm working on integrating nrf8001 with STM32, currently trying to write my own stack.
Upon reset, I read the DeviceStartedEvent, 0x81 and it shows "0x02 0x00 0x02", which...
After a fresh install of Keil (along with Legacy patches) and the SDK, I get the following messages when I try to open the ble_app_template_s110 project:
The project...
Hi All,
I use iot_ipv6_udp_client example on nRF51 DK.
I modified it and send data in one direction only (not receiving back).
Testing has shown that the maximum packet...
Hello,
I use S130 with NUS style connections as central and device at same time. It works nice and performance is good but when i run scan, performance become very poor...
Hi,
I'm using S130 with SDK 9.0.0 and as central, I'd like to read values for more than one characteristic on a peripheral. I do so in BLE_GATTC_EVT_CHAR_DISC_RSP by firing...
Hi,everybody!
Recently,i use nrf51422 as peripheral programming s310 ant_ble_hrs example in sdk6.0 and use nrf51822 As center programming s210 hrs example in sdk6.0. I find...
Suppose I have a lot of very small characteristics (1 or 2 bytes) to send lots of notifications on. They are all updated simultaneously, though the central doesn't care about...
It seems daft, but the ble_heart_rate_template_with_battery_service example in the nRF8001 Arduino SDK does not use the nRF8001's Battery Monitor!!
Instead, it just uses...
I'm working on an application that uses the persistent storage manager to store some calibration data. I thought I had everything working well, but after higher volume testing...
Hi,
I have already developed (and almost finished) an application with SDK 8.1.1
As you now when I created the application starting from an SDK example, the project under...
Confirm all the certifications the product nRF8001 is currently holding (or in the process to be awarded).
Is the nRF8001 certified/approved to be commercially used in...
Hi there,
As per title, the Ble bandwidth test on my Blend Micro is not connecting to the nRF UART app on iOS 8. I tap connect and it just says 'scanning....'. Could you...
I am trying to use the iOS nRF Temp app with the nRF8001 D chip. I have tried the ble_temperature_broadcast example from the nrf8001 SDK. The serial terminal shows successful...
I have this odd issue which creeps up in field testing. Upon a button push the board goes immediately to System Off. 99.99% of the time Button pushes are handled normally...
