Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
My project uses ESB for communication. In our hardware design, nrf5340 + FEM is used. Nrf5340 uses two GPIO link FEM chips to switch between PA mode and LNA mode. May I ask...
Dear Nordic,
I am considering to make a board that includes an nRF5340 + display. I am looking at a display that supports QSPI and I was wondering if the nRF5340 QSPI can...
Hi,
I am learning nRF52840 development and making a sensor device.
The datasheet of the nRF52840 chip says:
Regulated supply for external components up to 25 mA
...
Hi,
I'm working on a project with the Nordic nRF9160 Development Kit and am trying to send Bluetooth beacon data from the nRF52840 chip to the nRF9160 chip using UART and...
Hello,
I try to enable the LE Data Packet Length Extension. According to the available documentation, it should be as simple, as adding `CONFIG_BT_USER_DATA_LEN_UPDATE=y...
When loading empty software (zephyr based) into the nRF9151, the nRF9151 uses roughly 4mA and when erasing the IC, it uses 5.8mA.
Does zephyr not include a power down mode...
Hello!
I am porting a nRF Connect v2.9.0 application from a nRF52 to the nRF54L15.
We are using PPI/EGU to get exact measurements for some BLE radio events for some optimizations...
Hi,
We are developing application software on the nrf9161dk that uses the little FS file system running on external FLASH. Most of the application development has been completed...
Hi
I want to use P0.18 gpio as output pin and not as reset for nordic.
I am using ncs v2.0.0.
I have added
CONFIG_GPIO_AS_PINRESET =n in prj.conf
and when i...
Hello,
I have a Nordic Thingy:91, and I need to perform continuous wave (CW) transmission tests in LTE. To achieve this, I plan to develop custom firmware that alternates...
Hello Everyone,
We are working on a new product using the nrf52840 and OpenThread.Our current product uses the Azure IoT Hub and we were wondering if we could use the library...
Hi,
I defined __STACK_SIZE as compile/build flag. It has no effect according to GCC output after building is done.
Chip is nRF52840.
I tried to set fixed stack size...
Based on the message on the following page, nrfjprog has been deprecated and should no longer be used:
https://www.nordicsemi.com/Products/Development-tools/nRF-Command...
