Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I am trying to modify the https_client example from ncs\nrf\samples\nrf9160\https_client on Thingy91 so that it will retrieve an authentifcation token from AWS Cognito. So...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
The nRF52832 acts as SPI Slave and we want to wake up from Deepsleep when...
Hi
New to using EGU, trying to use it to implement software interrupts. How do I capture an Event?
I can see how to trigger and clear an event using -
nrf_egu_task_trigger...
In the function ble_init, I am getting an undefined reference to sd_softdevice_enable during the linking process. I see that in nrf_sdm.h there is SVCALL(SD_SOFTDEVICE_ENABLE...
Hello,
I am looking for the cost effective simultaneous central+peripheral solution using nrf BLE.
The nrf52810 seems to be hardware capable of doing this but I am...
Hi, I am creating custom ble service.there i need to perform
1. character - READ , NOTIF
2. character - WRITE READ
3 . character - READ,WRITE, NOTIF
I achieved ...
Hi
I'm on a custom board with NCS 1.2.0 and modem firmware 1.2.0.
We have implemented agps, and testing with 2 units with agps colocated with 1 unit without agps. All...
Strange device crash on deprovisioning.
This is probably something incredibly stupid, but I have been fighting this problem for a week and don't know where to turn.
I...
Hello
I program the example code peripheral " ble_app_hrs -pca10040e -s112" on nRF52810 and central " ble_app_hrs_c-pca10040 -s132" on nRF52832 .
I used nRF Toolbox on...
Hi,
we are working with Nrf52 and do not need/use Bluetooth, i.e. our devices will not have the Softdevice stack installed.
I was informed that for the radio certification...
Hello, I am using nRF52840, SDK 16, SoftDevice s140 with SES. I want to configure my device first in connectable mode and then in non-connectable beacon mode. sys_advertising_init...
Hi,
The situation is very simple; I try to use the CoAP Utils library to simplify CoAP usage in an application running on the nRF9160 DK ( https://developer.nordicsemi...
