Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am operating in a "peripheral" configuration, with bonding enabled. "BLE_GATTS_EVT_WRITE" occurs when notification is permitted...
We're porting over some software to the Arduino Nano 33 BLE Sense. This board comes with an nRF52840 clocked at a max. of 64MHz. However, the same code runs about 2x slower...
I want to send Tx power in advertisement packet.
Currently I am using following code.
int8_t txpower_level;
static ble_advertising_init_t init =
{
....
Customers use nrf52810 flash program to store data, but want to know what flash start and end address can be written, please point out that you can refer to that document...
Dear Nordic Semiconductor
I am using device:
NRF51802 bluetooth 4.0
Product Introduction:
Features:
1.Adopt NRF51802 bluetooth 4.0 BLE SOC
2.ARM CORTEX-M0
3...
Hi , I use the pc-ble-driver to developer desktop tools, like nRF Connect. Unfortunately, I don't know Java. I‘ve tried to used examples that work(heart_rate_collector and...
Hello,
We use a custom interface board to program and run test programs on our series of tiny BLE modules based on nRF52xxx series (ISP1507, ISP1807, ISP1907).
Our interface...
Hello ,
The test of CPS/SEN/SPE/BI-04-C [Procedure Already In Progress] failed.
While this test, the tester sometimes received the unexpected ATT Disconnect which our...
I want to advertise a data in ble_app_uart continuously after equal interval of time. Can you please give me some clue. I don't want to use beacon here
Hi,
I am currently trying to implement a beacon scanner and want to filter out all advertisements except beacons. Is there something in the beacon advertising packet that...
Hello everyone,
I am working with nrf5_SDK_16.0.0 and using VS Code as IDE. When I open the "stdint.h" header file in VS Code, the 16-bit compiler is enabled:
But, I...
Dear sir,
If I dump the hex file of this path "nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_uart\hex" then the code is working fine. But if I dump the hex file...
