Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
Is there a way to disable bonding? I am having issues when I delete the paired device from my phone. After I delete the pairing, nordic still has the stored keys for...
We are developing a Bluetooth device around the nRF52840 SoC. The time has come to investigate the production part of things.
Since we have been developing and designing...
Hi Devzone:
Where can I find full document on how to use nrf_power_gpregret_set?
Background: I am planing to do buttonless DFU without BLE but through usb cdc acm.
After...
Dear support team, we are trying to make the device ST IIS2DLPC (accelormeter) talk via SPI to the dev board PCA10040
We are using the evaluation board STEVAL-MKI191V1 wich...
Hello,
I am trying to build the lwm2m_client sample on my ubuntu 16.04 machine. I tried building for nrf9160_pca10090ns and nrf9160_pca20035ns The build fails with:
...
Hi,
I am using SEGGER/SEGGER Embedded Studio for ARM 4.12, I used Two working Examples ble_app_gatts_c_pca10040_s132 and flash_fstorage. I am getting these errors "undefined...
Hello,
For our project I'm using a LIS2DH (accelerometer) that is supposed to trigger an interrupt on its pin INT1 when a movement is detected.
I use nRF52832. Before...
Hi
I'm not familiar with C language, I tested the saadc example in SDK, it worked well in P0.02
But I dont see how they set CH[X].PSELP or CH[X].PSELN (V(p) and V(n))...
Hi
Using PCA 10040A , SDK 16.0.0 and Segger Studio.
I would like to generate a short accurate *** on a GPIO , probably 250 nano seconds duration. So I am looking at using...
Hello All,
my application should record acceleration data and time stamps.
After recording the data block from start to end should be transmitted.
I only know that...
Hello, guys.
In our current project, we need to periodically update AWS IoT Server with the data from local sensors. So far, thanks to the cloud_client example and your...
Hi
For a new project I'm looking for a cheap bluetooth chip. All my software resides in a PIC, because on PIC I have a lot of experience and I don't have the time to dedicate...
Hello all,
I am using NRF52840 and SDK 16 in central mode and added two UUID filters to the scan module for two different groups of peripherals . My application works fine...
Hi,
I am trying to send a test message in Server through mqtt and used the mqtt_simple example for that.
For the test I insert data_publish() function in main() like...
